Before you buy, check it isn't under a dangerous recall.

In passenger-side airbag inflators, inadequate moisture protection of the gas generant can result in degradation when exposed to repeated temperature cycling in high-humidity environments. This may cause the inflator container to rupture …

In the Electronic Stability Program (ESP), due to an inappropriate control program, when the collision mitigation braking system or adaptive cruise control with distance control is deactivated due to road condition changes …

The steering coupling, which connects the steering shaft and steering gearbox, has insufficient fastening torque on its coupling nut. This causes wear of the coupling during full-lock turns or low-speed steering reversal. …

In the brake booster, due to improper material selection of the vacuum pipe connection and improper manufacturing of the vacuum pipe (including connection), the vacuum pipe connection may fracture under driving or …

In vehicles where the passenger seat airbag inflator has been replaced with a countermeasure unit, the airbag exhaust port is undersized. During airbag deployment, this can cause cracks in the airbag mounting …

In the automatic transmission select lever, improper welding equipment settings may result in insufficient welding between the select lever and bracket. This may cause the weld to fracture during lever operation, rendering …

The seal shape at the piston section of the brake master cylinder is inadequate, which may cause the seal to roll up when the brake pedal is depressed. This can result in …

In the electric parking brake system, some parking brake calipers have insufficient gear strength due to improper manufacturing. Motor actuation force may cause gear failure, potentially resulting in inability to release the …

Due to insufficient cooling during resin molding of the fuel tank, molding defects occurred at the fuel pump mounting screw boss, which may reduce seal performance with the fuel pump installed. As …

The front wiper motor has inadequate waterproofing in the front deck area. Water seeping between the front deck garnish and windshield glass can enter the motor interior, causing internal corrosion. In the …

On the opening/closing side covers of the loading device of refuse collection vehicles, the fixing method between the lower cover and upper cover is inadequate. Consequently, the fastening of the lower cover's …

The owner's manual lacks a compatibility matrix table for i-Size (iSIZE) child seats by seating position, failing to comply with safety standard Article 22-3, detailed notification Article 30 (UN Regulation No. 16, …

1. In the engine cooling system, improper coolant temperature control can cause the coolant temperature to rise rapidly when the engine is started under specific ambient temperatures and sudden acceleration occurs. This …

1. In the engine cooling system, improper coolant temperature control may cause coolant temperature to rise rapidly after engine start-up followed by hard acceleration under specific ambient temperatures. The resulting thermal stress …

Driver-side or passenger-side airbag inflators may have inadequate moisture protection of the gas generant. Repeated temperature fluctuations in high-humidity environments can degrade the gas generant, potentially causing inflator container rupture during airbag …

Front wiper arm attachment nuts on the wiper motor shaft may have insufficient torque due to improper fastening, causing the nut to loosen during wiper operation. Continued use in this condition allows …

In cooling system hoses (radiator drain hose, radiator reservoir tank hose) and fuel system hoses (fuel supply hose from tank to engine), improper assembly instructions during manufacturing have caused clips that secure …

In small buses, the automatic transmission fail-safe control program is inappropriate. If the vehicle speed sensor malfunctions, fail-safe does not activate, and the transmission may unexpectedly downshift to a low gear during …

On large trucks, the stabilizer arm of the rear axle air suspension has insufficient strength. Repeated turning can cause cracks to develop in the arm. If operation continues in this condition, in …

In ladder fire trucks, the steering idler arm lacks sufficient strength. Repeated full-lock steering operations can cause cracks to develop in the arm. Continued use may result in arm fracture in the …

In combination tail light and brake light assemblies, improper socket manufacturing results in insufficient press-fitting of the bulb retaining clip. Consequently, the clip may disengage due to vibration during operation, and if …

Due to inappropriate control programming in the auxiliary power module, during the transition from idle-stop deceleration to re-acceleration, the module may incorrectly judge the high current flowing through the starter-generator as excessive …

The wire harness in wheel loaders has insufficient waterproofing, allowing rainwater and other moisture to enter inside the wire harness cover. When this moisture travels along the wiring and reaches the connector …

The capless fuel inlet cap seal material is inadequate, causing loss of sealing integrity when exposed to moisture from detergents and other sources. This allows rainwater and other contaminants to enter the …

In the fuel system, improper manufacturing of the high-pressure fuel pump can cause wear to the piston that pressurizes fuel in the pump. This results in reduced fuel supply, and continued operation …

Voltage fluctuations supplied from the battery and manufacturing variations in the fuel pump may cause premature wear of internal components. Continued use in this condition can lead to progressive wear, resulting in …

In diesel engine fuel systems, improper manufacturing of fuel supply hoses has resulted in non-uniform wall thickness. Consequently, fuel supply hoses may be damaged by fuel pressure fluctuations, potentially leading to fuel …

The rear shock absorber lower mount lacks sufficient strength. Under rough road conditions, impact may cause cracks in the lower mount. Continued use allows cracks to propagate, potentially leading to lower mount …

In the direction indicator of shovel loaders, the component controlling the flashing speed is inappropriate, resulting in some units having fewer flashes than specified in Safety Standard Article 41. Therefore, non-compliance with …

In the engine cooling system, engine oil cooler hoses may be improperly assembled such that the retaining bracket (clamp) is not fastened. Due to oil pressure, the hose may become detached, causing …