Before you buy, check it isn't under a dangerous recall.

Large bus heater hoses have insufficient strength, and internal reinforcement threads may break under water pressure. Continued use in this condition risks heater hose failure under pressure, causing coolant leakage and reduced …

Due to improper software in the central electronic module, power is not supplied to the left tail light, and the left tail light may not illuminate.

The circuit short-circuit detection software of the speed-sensitive power steering system is inappropriate, which may cause false detection of circuit short-circuits during driving. This fixes the power steering assist to a low-assist …

In the rear suspension, improper tightening of the left and right toe link assembly nuts may cause them to loosen during use. Continued operation in this condition can result in play, and …

In the intake air cooling system (intercooler) piping of supercharged engines, some units have insufficient fastening force between the intercooler hose and intake pipe. As a result, the hose may fail to …

On four-wheel drive vehicles, the rear brake drum removal screw hole is positioned improperly, allowing water to enter the brake drum through this hole. When parked in low-temperature conditions, the infiltrated water …

The resin cover material in the license plate light is inadequate. Prolonged use may cause the cover to melt from bulb heat, potentially resulting in vehicle fire.

In the high-pressure fuel pump of all-wheel-drive vehicles, the filter section has an improper shape. When there is excessive moisture in the fuel tank, water in the fuel line may freeze due …

The fuel pressure sensor fastened to the engine fuel supply rail may have inadequate fastening torque. Engine vibration and similar factors can cause the fastening to loosen. This may result in fuel …

Driver-side airbag inflators may experience improper moisture management after gas generant charge during manufacturing. External temperature and environmental factors during use can cause the gas generant to expand and decrease in density. …

Driver-side airbag inflators may experience improper moisture control after propellant charge filling during manufacturing. Under the influence of external temperature and other factors during use, the propellant may expand and decrease in …

The airbag control computer's acceleration sensor was manufactured improperly, causing cracks to develop in the internal deployment signal output circuit, which may result in circuit disconnection. This may cause the airbag deployment …

The bracket strength securing the driver's seat to the vehicle body is insufficient. Repeated loading on the seat can cause cracks in the bracket. Continued use may result in abnormal noise and …

The internal lock nuts on both left and right front forks are improperly tightened and may loosen during use. This can cause abnormal noise and compromised ride stability. If use continues in …

In the power transmission device, the shaft section of the third gear has insufficient strength, and cracks may develop in the shaft. If use continues in this condition, the cracks will propagate …

The electronic control module of the engine has improperly manufactured internal circuit board components. Excessive current flows to the injector control component on the internal circuit board, damaging said component. As a …

The internal circuit of the microcontroller controlling the multi-information display is defective. When the ignition switch is turned on, the multi-information display may fail to illuminate. As a result, if the vehicle …

Due to improper programming of the engine control unit, when high engine load conditions exist and certain shift operations are performed, the engine may stall.

Due to improper airbag control computer programming, the deployment signal for the driver and passenger seat airbags may not be issued in certain collision types. As a result, the driver and passenger …

Certain rear wheel rims have improper finishing during manufacturing. This results in poor tire seating, allowing air to leak between the rim and tire bead, potentially compromising riding stability and causing loss …

The speed sensor mounted on the front wheel axle assembly has an inappropriate structure. During operation, the rotor tilts, causing lubricating grease in the inner diameter sliding surface to be expelled and …

The turn signal relay mounting method is inadequate, allowing electrical wiring connected to the relay to flex during vehicle vibration. Continued operation may cause the wiring to fracture from repeated flexing, resulting …

In heavy-duty trucks, improper engine control program and exhaust gas recirculation (EGR) valve settings cause frequent manual regeneration interruptions of the DPR (diesel particulate filter). When post-injection fuel enters the EGR cooler, …

In the hood locking mechanism, due to improper manufacturing of the striker, the striker may disassemble due to vehicle vibration. As a result, the hood lock may disengage, and in the worst …

The driver-side SRS airbag inflator has improper moisture management of the gas generant after filling during manufacturing. Due to external temperature and other environmental factors during use, the gas generant may expand, …

The driver-side SRS airbag inflator has inadequate moisture control of the gas generant after charging during manufacturing. Due to external temperature fluctuations during use, the gas generant may expand and lose density. …

In diesel vehicle fuel injection systems, the fuel pipe connecting the fuel pump to the fuel injection nozzle has insufficient strength. Fluctuations in fuel pressure may cause cracks to develop in the …

In the ball joint connecting the lower arm and knuckle arm of the front suspension, improper management during component transport after fastening the knuckle arm and ball joint can cause the transport …

In the rear left and right seat belts, improper drawing instructions for retractor component parts result in insufficient clearance between the lock mechanism's plastic lever and wheel. Consequently, when attempting to pull …

On vehicles equipped with a spare tire, the flange nut design that secures the spare tire and carrier to the vehicle is inadequate. Vehicle vibration causes the flange nut to gradually loosen, …