In the Engine Management System's ECM (Electronic Control Module), the abnormality detection method for throttle position sensor signals is inappropriate. Noise generated by vehicle vibration may be incorrectly identified as an abnormality. …
Triumph Tiger Explorer 2012–2013
Triumph Tiger Explorer XC 2012–2013
Triumph Trophy 2012–2013
Triumph Trophy SE 2012–2013
In the ambulance automatic transmission, some oil cooler hoses have insufficient clamping force, which may cause the hose to detach, resulting in oil leakage and loss of vehicle mobility.
Nissan Paramedic 2013–2014
The connector design in the rear combination light bulb carrier is inadequate, causing contact failure due to vehicle vibration. When the light is illuminated in this state, the connector may overheat. Repeated …
BMW BMW 525i 2007–2009
BMW BMW 530i 2007–2009
BMW BMW 540i 2007–2009
BMW BMW 550i 2007–2009
BMW BMW M5 2007–2009
The alternator harness routing in blood collection vehicles is improper. Vibration from driving may cause the harness to contact the exhaust gas recirculation (EGR) cooler. Continued use in this condition may result …
Hino Hino Melfa 2011–2012
In truck fuel tanks, the fuel tank band was secured with excessive tightening torque, causing excessive stress on the spot welds of the internal baffle plate (a partition that suppresses fuel sloshing). …
Isuzu Elf 2005–2006
Nissan Atlas 2005–2006
The mounting position of the left and right side reflectors on tractors (overall length exceeding 6 m) is inappropriate, failing to comply with the dimensional requirements of Safety Standard Article 35-2 (side …
ＵＤトラックス Quon 2011–2013
In the Keyless Operation System Control Unit (KOS ECU), a manufacturing defect in the internal reset IC may cause the reset IC to malfunction in extremely low temperatures, resulting in microcontroller shutdown …
Mitsubishi RVR 2011–2012
Mitsubishi Outlander 2011–2012
Mitsubishi Mirage 2011–2012
Certain hybrid large-capacity transit buses have inverters with insufficient durability and reliability in their current conversion devices. Inverter failure may prevent the drive motor and auxiliary motor from operating, causing the hybrid …
Mitsubishi Fuso Aero Star 2008–2010
The brake plate, a component of the braking system, has an improperly designed groove intended to prevent interference between the brake shoe and brake plate. Concentrated tensile and compressive forces during braking …
トレクス ― 2009–2013
The brake plate, a component of the braking system, has an improperly designed groove intended to prevent interference between the brake shoe and brake plate. Tensile and compressive forces concentrate in the …
日通 - 2008–2013
In the fuel tank, improper temperature management during the filler pipe welding process results in insufficient weld strength at the filler pipe joint. Continued use in this condition may cause the weld …
Mitsubishi Mirage 2013
In the engine, an incorrect corrosion preventative was applied to the sealing bolts that restrict rocker arm shaft rotation. Engine heat causes the fastening torque to decrease, resulting in bolt loosening and …
Honda 400X 2013
Honda CB400F 2013
Honda CBR400R 2013
In vehicles equipped with diesel turbo engines, some intercooler hoses connected to the throttle chamber have insufficient clamp fastening force. Continued use may cause the hose to become disconnected due to engine …
Isuzu Como 2012–2013
Nissan NV350 Caravan 2012–2013
In the controller for the forward/reverse hydraulic clutch of the power transmission device, due to an inappropriate travel control program, unintended sharp turning may occur when left steering is immediately performed after …
ヰセキ TPC153 2003–2013
ヰセキ TPC183 2003–2013
Due to improper assembly procedures during wheel loader manufacturing, some rear axle trunnion fastening plate bolts are missing washers. Continued use in this condition may cause bolt torque to loosen, resulting in …
キャタピラー 910H 2013
In the hybrid system, due to improper control software, unexpected thermal stress is applied to the boost circuit elements during high-load driving such as acceleration. Consequently, the element may be damaged during …
Toyota Prius 2009–2014
In the 7-speed DCT automatic transmission of hybrid vehicles, the sleeve does not move smoothly on the hub of the 1st gear inside the transmission. As a result, the 1st gear may …
Honda Vezel 2013–2014
Honda Fit 2013–2014
The throttle pedal lever is made of inadequate material, and repeated operation may cause the lever to fracture and detach. If the throttle pedal lever detaches, the pedal cannot be depressed, preventing …
Aston Martin Aston Martin DB9 Volante 2007–2013
Aston Martin Aston Martin DB9 Coupe 2007–2013
Aston Martin Aston Martin DBS Volante 2007–2013
Aston Martin Aston Martin DBS Coupe 2007–2013
Aston Martin Aston Martin V12 Vantage S 2007–2013
+11 more
The pressure gauge displaying the internal pressure of the brake system pressure vessel does not indicate the minimum effective operating pressure of the equipment on its scale, failing to comply with safety …
ニッセキ HTR306 2012–2014
ニッセキ HTR407 2012–2014
The headlight electrical wiring connector terminals for the bulb have insufficient thermal margin. Heat from the bulb-side terminals reduces the contact pressure of the electrical wiring terminals. Continued use may cause the …
Yamaha YZF-R1 2009–2013
Yamaha Majesty YP250 2009–2013
The dashboard trim finishing work was not performed. In the event that the passenger seat airbag deployment is necessary, it may not deploy properly. Additionally, unexpected dashboard damage may occur during airbag …
BMW BMW X3 xDrive 20i 2012–2013
In refuse collection vehicles equipped with plunger-type hydraulic pumps (manufactured by Fuji Heavy Industries Ltd., trade name: Fuji Mighty), the hydraulic pump mounting bracket has insufficient strength, and cracks may develop in …
Isuzu Elf 2007–2013
Isuzu Forward 2007–2013
In mechanical automatic transmissions for light-duty trucks and buses, internal cleaning during valve body manufacturing is inadequate, leaving foreign material in the hydraulic circuit. This can cause malfunction of the clutch control …
Mitsubishi Fuso Canter 2010–2013
In large buses, improper assembly of the idler pulley (such as bearing press-fitting) results in excessive starting resistance on the pulley. Continued operation in this condition may cause abnormal noise and bearing …
Mitsubishi Fuso Aero Ace 2010–2013
Mitsubishi Fuso Aero Queen 2010–2013
ＵＤトラックス Space Arrow A 2010–2013
ＵＤトラックス Space Wing A 2010–2013
In the automatic transmission, the fastening process for the nut connecting the shift cable to the transmission is inadequate, resulting in some nuts being insufficiently tightened. Continued use in this condition may …
Toyota Wish 2013–2014
The hydraulic pump hose inserted into the suction-side pipe of the hydraulic pump that supplies hydraulic fluid to the traveling hydraulic motor and work equipment has inadequate fastening clip tightness due to …
コべルコ SK125W 2006–2013
In hydraulic pumps driven by the engine via PTO (Power Take-Off) components, which supply hydraulic pressure to braking systems, power steering systems, and snow removal equipment, the hydraulic pump input shaft exceeds …
ニイガタ Niigata NR302 Rotary Snow Plow 2013–2014
ニイガタ Niigata NRN302 2013–2014
Genuine accessory driver-side floor mats (rubber mats) were incorrectly sold for different vehicle specifications. When installed, the shape does not fit properly and may interfere with the accelerator pedal, potentially hampering smooth …
Mercedes-Benz E250 2013
Mercedes-Benz E250 Station Wagon 2013
Mercedes-Benz E300 2013
Mercedes-Benz E300 Station Wagon 2013
Mercedes-Benz E350 BlueseTEC 2013
In concrete mixer trucks, the clearance between the pump unit deck and the inside tire of the rear left axle is insufficient. During operation on uneven terrain, the inside tire may contact …
Hino Dutro 2001–2013
Isuzu Elf 2001–2013
In the rear axle, a combination of manufacturing tolerances creates a gap at the contact point between the rear-wheel-drive input shaft and bearing, which can cause rust and wear at the contact …
BMW BMW F800S 2006–2009
BMW BMW F800ST 2006–2009