Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
10559 recalls on record · page 233 of 352
The pipe section within the upper flange of the fuel pump has insufficient wall thickness. Due to aging and operational environment exposure, cracks may develop in this pipe section. In the worst …
Improper tire toe-in adjustment may cause tire tread to contact the leaf spring when wide-tread tires are installed and the steering wheel is turned to its maximum angle. When wide-tread tires are …
The stabilizer bracket strength on independent front suspension vehicles is insufficient. Repeated high-center-of-gravity cornering and similar maneuvers can cause cracks to develop in the bracket. Continued use in this condition allows crack …
Prolonged air conditioning operation in high-humidity conditions may cause condensation in the air conditioning duct, which can drip onto the ECU controlling the mechanical automatic transmission. This may result in shift inability …
The air tank for the parking brake (wheel park) lacks a check valve. If air lines outside the brake system fail, the parking brake may engage and become unable to release.
The throttle housing mounted on the handlebar has an improperly positioned drainage hole. Water that accumulates inside the housing from car washing and similar activities can seep into and remain within the …
Improper routing of the fuel pump electrical wiring inside the fuel tank may cause the negative wire terminal to interfere with the positive wire terminal. Engine vibration can abrade the negative wire …
The engine lacks a blow-by gas recirculation device, failing to comply with road transport vehicle safety standards.
Some vehicles equipped with panoramic glass roofs have insufficient adhesion on the roof panel. Continued use in this condition may result in the roof panel detaching and obstructing other traffic.
The brake light switch contact has insufficient electrical load capacity. Repeated brake operation causes contact wear, resulting in brake light non-illumination, shift lever immobility from park position, or inability to restart.
In the speedometer, the vehicle speed signal amplifier is mounted in an improper position, which may cause the amplifier to be subjected to strong vibrations from the transmission and other components. If …
The exhaust pipe bellows section has an improper structure. Engine vibration causes the bellows to wear and crack. Continued use may result in exhaust gas leakage and increased noise.
Some ball joint fastening nuts connecting the suspension arm and hub carrier of the damper are insufficiently tightened. If left in this condition, the nuts may loosen, and in the worst case, …
Insufficient thermal shielding of the voltage regulator may cause performance degradation due to heat exposure. This can result in battery charging failure, and in the worst case, engine shutdown during operation with …
The anchor plate of the side stand spring mounted on the vehicle undercarriage may have improper welds, preventing the side stand from retracting correctly. Continued operation in this condition may allow the …
Front wheel brake hoses have improperly crimped fittings. Under heavy or frequent braking, heat may soften the hose, causing the fitting interface to loosen and brake fluid to leak. In worst case, …
The external operating handle of the emergency exit door has insufficient strength. When operating the handle, pulling before unlocking may cause the handle to fracture. This could prevent the door from being …
The exterior emergency exit door handle lacks sufficient strength. When operated, pulling the handle before disengagement may cause it to break. This could result in inability to open the door from outside.
The external operating handle of the emergency exit door has insufficient strength. When operating the handle, pulling it before unlocking may cause it to break. This could prevent the door from being …
In the variable geometry turbocharger (VGS) of heavy-duty truck engines, turbine blade strength is insufficient. Resonance at high engine speeds may cause turbine blade fracture. Continued operation risks white smoke generation and …
The drive pinion bearing assembly adjustment in the rear axle differential is inadequate on some units. This can cause bearing damage during short operating hours, resulting in loss of mobility.
The drive pinion bearing assembly adjustment in the rear axle differential is improper in some units. This can cause bearing damage during brief operation, resulting in loss of drive capability.
Ignition coils in the engine may develop cracks in the coil body due to improper material composition. As a result, the coil voltage may not reach the required ignition voltage, causing spark …
The exhaust gas recirculation (EGR) pipe lacks sufficient structural strength. Thermal expansion and contraction of the pipe due to exhaust heat can cause cracks to develop, resulting in abnormal noise and exhaust …
Sound-deadening auxiliary material is installed near the front seat belt retractor with belt tensioner (a device that instantly retracts slack in the seat belt upon collision) located at the lower center pillar. …
The lower mounting portion of the rear-wheel shock absorber has insufficient structural strength. Due to vibration during operation, cracking may occur in the welds of the mounting portion. Continued use could result …
Due to improper manufacturing processes, pistons may develop internal delamination and crack propagation. Continued use may result in engine failure and loss of vehicle operability in severe cases.
Due to improper manufacturing processes in the engine pistons, internal delamination may occur, leading to crack propagation. Continued use in this condition could result in engine failure and loss of vehicle drivability …
In the front axle mounting section (pivot metal), improper casting process results in insufficient material strength in some units. This can cause the mounting section to fracture, leading to front axle detachment …
The electrical circuit of the integrated unit controlling the key interlock mechanism (which prevents key removal when the automatic transmission is not in P position) is improperly designed. Repeated ignition off operations …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.