Back door latch may have improper resin body dimensions due to manufacturing defect, preventing the lock mechanism from engaging properly and potentially allowing the door to open during operation. In worst case, …
Mazda AZ-Wagon 2010
Mazda Carol 2010
Nissan Roox 2010
Suzuki Alto 2010
Suzuki Alto Lapin 2010
+2 more
On vehicles equipped with 14-inch steel wheels, the full wheel cap has a large outer diameter. When tires experience heavy loads due to curb strikes or similar impacts, the deformed tire sidewall …
Nissan Roox 2008–2010
Suzuki Palette 2008–2010
The module (composed of two sections) mounted on the steering column that relays horn switch signals, airbag activation signals, and other signals has a gap at the module body joint. Due to …
オペル Astra H 2004–2006
オペル Zafira B 2004–2006
On large-capacity tour buses, the mounting position of the air conditioning resistor is improper, causing contact between the resistor and its cover in some units. This may result in a short circuit …
Isuzu Isuzu Gala 2010
Large tour bus: The mounting position of the air conditioning resistor is improper, causing some units to contact the resistor cover. This may result in short-circuiting between the cover and resistor, creating …
Hino Hino Selega 2010
A different material was used in the component that retains the position of the turn signal switch operating knob, which can cause rust to form inside the switch due to rainwater and …
Honda Today 2007–2009
The commutator in the electric fuel pump motor may wear prematurely due to improper manufacturing process, potentially causing the fuel pump to become inoperative, resulting in engine shutdown and inability to restart.
BMW BMW X5 3.0 si 2007–2008
In the head-side impact protection airbag, improper assembly of the airbag may cause twisting in the airbag deployment area. If twisting occurs, the airbag will not function properly.
Volvo Volvo XC60 2009
During fuel tank manufacturing, insufficient moisture removal after submersion testing for air-tightness verification has left water residue inside fuel pump connectors. Continued use allows connector terminals to corrode; in worst case, terminal …
Mazda Biante 2009–2010
Mazda Premacy 2009–2010
The flange soldering that connects the hydraulic pump-side hose to the gearbox-side hydraulic hose of the power steering unit may be defective. This can result in oil leakage from the connection point, …
ロールスロイス Ghost 2010
In the engine compartment, improper routing of alternator wiring, starter motor wiring, and engine control wiring causes contact with the power steering return pipe. Vibration and other factors may damage the return …
キャデラック DTS 2010
The brake pipe retaining bracket on the rear brake pipe of the braking system lacks adjustment tolerance. This causes misalignment when securing the brake pipe. Continued use in this state can result …
日立 ZX145W-3 2008–2010
Injuries — The product poses a risk of injuries (road accident) due to the loss of efficiency of the parking brake noted by an absence of force when using the parking brake …
Citroen e2*2001/116*0360*07
In vehicles equipped with a washer fluid freeze-prevention heater installed as a dealer option, the waterproof O-ring in the heater control circuit section has insufficient clamping force. This may allow washer fluid …
Daihatsu Bego 2006–2009
Toyota Rush 2006–2009
In vehicles equipped with a washer fluid antifreeze heater installed as a dealer option, the O-ring sealing the heater control circuit is insufficiently compressed, allowing washer fluid to infiltrate the control circuit. …
Toyota bB 1995–2009
Toyota Isis 1995–2009
Toyota Aristo 1995–2009
Toyota Alphard 1995–2009
Toyota Allex 1995–2009
+11 more
The intermittent relay contacts mounted on the wiper switch have improper contact arrangement. Frequent intermittent operation can cause contact wear and dropout, leading to short circuits. This can result in wiper malfunction …
Hino Hino Liesse II 1999–2004
Toyota Toyota Coaster 1999–2004
Toyota Toyota Coaster Big Van 1999–2004
In the manufacturing process of the power steering hydraulic pump, some units have the connection fittings that join the pump to the high-pressure piping installed with improper fastening torque. Continued use may …
Mercedes-Benz C200 CGI 2009–2010
Mercedes-Benz C200 CGI Station Wagon 2009–2010
Mercedes-Benz C250 CGI 2009–2010
Mercedes-Benz C250 CGI Station Wagon 2009–2010
Mercedes-Benz C300 2009–2010
+17 more
In large-capacity high-speed buses, some units have insufficient bearing grease fill in the drive wheels. Continued use in this condition may result in inadequate lubrication of the bearing, potentially leading to loss …
Mitsubishi Fuso Aero King 2008–2010
In the primary brake line connecting the master cylinder and hydraulic control unit (HCU) in the engine compartment, the connection end of the HCU-side line has an improper shape, resulting in insufficient …
Chrysler Jeep Wrangler 2010
Chrysler Jeep Wrangler Unlimited 2010
Wheel mounting bolts may be improperly tightened. Continued use in this condition could result in bolt loosening and, in the worst case, wheel detachment.
キャタピラー 910H 2010
The short-circuit terminal for inadvertent deployment prevention during maintenance, provided within the contact reel connector for the driver-side airbag, has improper connector molding. This may cause the circuit to short not only …
Volvo Volvo S80 2010
Volvo Volvo V70 2010
Volvo Volvo XC60 2010
Volvo Volvo XC70 2010
The axles used in semi-trailers and pole trailers have insufficient strength margin for their operating environment. Prolonged use may cause cracks to develop in the spindle portion. If operation continues in this …
日通 Container Semi-trailer 1969–1995
日通 Semi-trailer 1969–1995
日通 Pole Trailer 1969–1995
Injuries — A problem with the fuel pump wiring could cause the engine to stall during driving or make it impossible to restart the engine.
Lexus Production period 28 September 2004 through 28 February 2006
Injuries — If brake fluid is used that does not contain polymers, or contains only small amounts, part of a seal in the master brake cylinder could become dry and a small …
Lexus Production periods affected:GS 17 Sep 2004 through 28 Feb 2006,IS 27 May 2005 through 20 Mar 2006,RX 10 Feb 2003 through 18 Feb 2006.
The clamp orientation for the starter electrical wiring of the engine is inappropriate, which may cause damage to the electrical wiring due to engine vibration and similar factors. If operation continues in …
Nissan - 1995–1999
The electric power steering control computer program is improper. When driving at high speed on a road surface with irregularities designed for lane departure warning, the computer may misinterpret vibrations from the …
Daihatsu Boon 2010
The electric power steering control computer program is defective. When driving at high speed on textured road surfaces designed for lane departure warning, road vibrations are misinterpreted, causing the power steering function …
Toyota iQ 2008–2010
Toyota Passo 2008–2010
Certain front suspension lower control arm mounting bolts have improper heat treatment. Continued use in this condition may result in bolt fracture.
Aston Martin Aston Martin DB9 Volante 2007
Aston Martin Aston Martin DB9 Coupe 2007
Aston Martin V8 Vantage Coupe 2007
Aston Martin V8 Vantage Roadster 2007
Due to improper frame assembly, when driving with studless tires installed and the steering wheel turned to its maximum angle, the tire may contact the drag link. Continued use in this condition …
Nissan ― 1999–2005
The engine control power relay contains an improperly manufactured internal diode, which may result in conduction failure. Continued use in this condition may cause engine start failure or engine stalling while driving.
Nissan Cube 2003–2006
Nissan Serena 2003–2006
Nissan Tiida 2003–2006
Nissan Tiida Latio 2003–2006
Nissan Note 2003–2006
+1 more