Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
5227 matching recalls · page 128 of 175
The rear suspension linkage structure is improperly designed, causing direct load application to the fixing bolts. Consequently, repeated driving on rough roads or similar conditions subjects the bolts to excessive stress, which …
In trailers equipped with air spring suspension systems where the axle and spring seat are secured solely by U-bolts, the fixation method is inadequate, causing U-bolt loosening and interference between the axle …
On four-wheel-drive fire trucks equipped with automatic transmissions, the clearance between the front-axle-drive propeller shaft and the automatic transmission oil-line mounting bolt is insufficient. During hard braking or similar events when the …
In the brake booster, some rubber seal rings that maintain airtightness in the atmospheric chamber have insufficient grease application, causing inadequate sliding of the seal rings. Continued use may result in deformation …
The battery storage case fastening method is inadequate, allowing mounting bolts to loosen due to engine vibration and similar forces. Continued operation may cause the battery to shift from its proper position …
The oil filler cap material on the left-side rocker cover is unsuitable, causing the cap to shrink due to heat exposure. Continued use may result in the cap dislodging due to internal …
The cruise control cancel switch mounted on the master cylinder has an improper internal seal structure, which can cause brake fluid leakage and contact corrosion. This may lead to switch overheating and …
Improper assembly of the rack bar within the power steering gearbox has damaged the oil seal in some units. Continued use may allow the damage to progress, resulting in oil leakage and …
The ball joint seal of the front lower control arm is insufficiently sealed, allowing water ingress into the joint. Continued use can result in premature internal corrosion and wear, potentially causing the …
In right-hand drive vehicles, the assembly of the fixing bracket (clip) between the clutch pedal and push rod may be improperly installed. Repeated clutch operation may cause the bracket to detach, and …
The red lens of the rear combination lamp, which serves dual duty as a tail light and brake light, has insufficient weather resistance. Prolonged exposure to intense solar radiation causes gradual fading …
The passenger-side airbag folding dimensions are improper, resulting in gaps between the airbag and its storage compartment in some vehicles. This causes increased lateral pressure during airbag deployment, leading to deployment from …
The electrical terminals of the brake light switch have an improper shape, resulting in insufficient contact at the terminal connection with the electrical wiring connector. If operation continues in this condition, vibration …
Some curtain airbag inflators have improper welds on the cutoff valve, causing gradual gas leakage. As a result, the curtain airbag may not deploy sufficiently during a side-impact collision, and in the …
The deployment structure of the driver-side airbag unit is improper, causing the airbag to interfere with the horn pad during deployment in some units. This can result in airbag damage and insufficient …
Due to improper fuel line circuit design, the check valve in the oil return line may degrade over time or become clogged with debris, reducing seal performance. When air is drawn into …
The mounting seat surface of the rear wheel hub nut is painted. During driving, vibration can cause the paint film to peel off, resulting in nut loosening. Continued use may lead to …
The fastening nut on the drive shaft flange of the power transmission system is under-torqued. Under forward and reverse load, the nut loosens, causing play between the flange and bolt. Continued operation …
Due to assembly process variation in the air hose connection between the brake valve and air tank, the air hose may contact the steering gearbox support. As a result, the hose can …
When the air-fuel ratio (AFR) sensor circuit—which detects oxygen concentration in exhaust gas—fails, the engine computer control becomes inappropriate. If internal sensor wiring breaks, proper air-fuel ratio cannot be maintained. Continued operation …
In spring-applied parking brake systems on three-axle vehicles with rear two-axle drive, improper breather hose installation allows water ingress into the spring chamber when traversing flooded areas, causing spring corrosion. Corroded springs …
The top cover and fan housing of heater units used for cooking and heating have insufficient heat resistance. When the device overheats, the top cover and fan housing may melt. Continued use …
The mounting portion of the intercooler air intake (hood air intake garnish) has an inappropriate shape, causing deformation due to engine compartment heat and similar factors, which generates high stress. Continued use …
The seal of the gas injection valve in the brake accumulator is insufficient, which may cause gas leakage. Continued use without correction will result in decreased gas pressure, and in the worst …
Injuries — The product poses a risk of injury. The possible loss of gear selection where it is not possible to engage the gear may lead to breakdown of vehicle or loss …
The gap between the child lock mechanism on the left rear door (a device that prevents children inside the vehicle from accidentally opening the rear door) and the door unlock lever is …
Certain fully hydraulic power steering pumps have weak springs retaining the rotor and some have improperly shaped valve plates. Repeated continuous steering operations can cause internal hydraulic fluid leakage within the pump, …
The dust sealing of the control valve in the brake hydraulic pump is inadequate, allowing fine foreign matter to enter the hydraulic fluid and potentially causing valve stiction. Continued operation in this …
Some brake pedal internal operating levers have been assembled with materials of different specifications, resulting in insufficient strength. With continued repeated use, the lever may fracture in the worst case, potentially rendering …
The lubrication grease injection port on the steering cylinder is mounted at an inappropriate position, creating a narrow gap between the propeller shaft and the injection port. Snow readily accumulates in this …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.