Before you buy, check it isn't under a dangerous recall.

In the Air Pressure Control System (APS), some units have an improperly designed air dryer regeneration control valve that cannot maintain air pressure integrity. This may result in air leakage, illumination of …

In the Air Pressure Control System (APS), some vehicles have an improperly designed air dryer regeneration control valve that cannot maintain air pressure sealing. This causes air leakage, resulting in warning light …

In the fuel system, the fuel pressure temperature sensor mounting housing attached to the fuel supply pipe has inadequate manufacturing control, resulting in insufficient housing strength in some vehicles. During use, cracks …

In the Air Pressure Control System (APS), some vehicles have an improperly designed air dryer regeneration control valve that cannot maintain air pressure sealing. This can result in air leakage, illumination of …

In the Air Pressure Control System (APS), some units have an improperly designed air dryer regeneration control valve that cannot maintain air pressure seal integrity. This may cause air leakage, illumination of …

Some rear brake caliper brackets have inadequate welds to the swing arm due to improper welding machine settings during manufacturing. When excessive force is applied to the bracket, the weld may fracture, …

The subframe for the thrust arm on the rear axle carrier has insufficient weld length due to improper manufacturing procedures. If the subframe welds separate during operation and the thrust arm detaches, …

In the braking system of agricultural tractors, improper hydraulic circuit design may allow air to enter the hydraulic circuit. Continued use in this condition may result in degraded brake performance.

Rear wheel brake calipers may have insufficiently tightened floating caliper mounting bolts due to inadequate maintenance of manufacturing equipment. During vehicle operation, these bolts may loosen and detach, causing abnormal noise. Additionally, …

In the 12V power wiring within the engine compartment, improper routing instructions during manufacturing result in wiring that interferes with body ground terminal points or other wiring, and some units lack insulation …

The coolant pump installed in diesel engines has an improperly designed bearing seal, allowing coolant to enter the vacuum circuit under controlled operation. This causes malfunction of vacuum circuit-related components, resulting in …

In recall notification 外-3276 (dated September 22, 2019), due to inadequate work instructions, wheel alignment adjustment was not performed after replacement of rear suspension arm fasteners. This may result in premature tire …

Oil filter cases used in brake hydraulic circuits of shovels and loaders, and in steering and differential lock hydraulic circuits of graders, have inadequate manufacturing methods and lack the durability required by …

The bipod strut connecting the lower rear suspension to the frame may have insufficient hardness due to improper manufacturing process. This component may fracture, causing the vehicle rear height to drop. In …

The secondary lock tab of the driver-side airbag connector was improperly installed during manufacturing, resulting in some units being installed in an incompletely locked state. This incomplete connection of the airbag connector …

The resin grab bar mounted at the rear of the vehicle has improperly assembled fixed-mounting nuts that do not maintain required strength and proper fitment. When heavy loads are applied—such as when …

(1) In the engine compartment wiring harness of agricultural tractors, improper routing causes contact between the wiring harness and the air conditioner condenser slide frame. Vibration during operation and friction with the …

(1) In agricultural tractor engine compartments, certain wire harnesses are routed improperly, causing contact between the wire harness and air conditioning condenser slide frame. Vibration during operation and friction with the slide …

(1) In agricultural tractor cabin front vibration damping material, improper assembly has resulted in sound-absorbing material being adhered over the protective film without removing the unnecessary protective film from the damping material …

(1) In agricultural tractor cabin front vibration damping material, improper assembly has resulted in cases where sound-absorbing material was adhered over the protective film without removing the unnecessary protective film from the …

In the steering system of agricultural tractors, the back pressure of the hydraulic circuit T-port is insufficient relative to the characteristics of the power steering controller. Under certain operating conditions, this can …

In the power steering mechanism, some power steering motors were manufactured with improper settings on the production line, resulting in units that deviate from the standard specification. As a result, when the …

In recall notification No. 3218 (dated June 11, 2019), due to inadequate work instructions, wheel alignment adjustment may not have been performed after replacing the nuts that secure the rear suspension arm. …

The front radar sensor (FRS) electronic control unit has improper programming, which may prevent correct recognition under specific conditions, such as collision scenarios with bicycles traveling ahead. As a result, the collision …

On the relay emergency valve mounting area of dolly-equipped bunk trailers, insufficient structural strength causes cracks to develop in the reservoir-port side mounting socket attachment and service-port side pipe fittings due to …

The relay emergency valve mounting area on dolly-equipped bunk trailers has insufficient strength. Vibration during operation causes cracks to develop in the reservoir port side mount socket mounting area and the service …

The Engine Control Unit program is inappropriate. When the throttle is slightly opened from idle, the air-fuel mixture drawn into the combustion chamber may become lean. In the worst case, engine stall …

The engine control unit program is inappropriate. During deceleration with the throttle closed, when the clutch lever is gripped with a small grip width, the air-fuel mixture drawn into the combustion chamber …

Certain primary brake plates lack proper machining, causing cracks to develop. Continued use may result in plate damage, and in the worst case, insufficient braking force when the brake pedal is applied, …

In light-duty trucks equipped with AMT (automated mechanical transmission) with easy access system, improper routing of wiring for the easy access system may interfere with the DC/DC converter bracket. This can cause …