Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
5188 matching recalls · page 88 of 173
Due to incorrect initialization of the body control module, when braking is applied, the amber rear turn signal may illuminate in addition to the brake light.
The ignition switch has lower rotational resistance than designed specifications. When a key ring or other attachments are installed on the ignition key, driving vibrations may cause the ignition key to move …
Non-compliant lighting is installed as the brake light.
The brake light mounting position is improper.
On large trucks equipped with spring brake chambers on the front axle, the ABS control valve bracket has an improper shape, resulting in insufficient clearance between the front right wheel spring brake …
The parking stand mechanism (used to support the vehicle body while the rear wheel remains in contact with the ground) has an inadequate design. The rear brake lever must be pulled with …
In large sightseeing hybrid buses, due to improper programming of the vehicle control ECU, after ABS actuation, the ECU may rarely remain in an active state recognition even when ABS is no …
In trucks, the ABS, mechanical automatic transmission, AT, or four-wheel drive control units mounted below the instrument panel may experience corrosion in the cooling circuit if coolant (antifreeze) maintenance in the heater …
In the front wheel brake, due to improper positioning of the inner wire casting at the cable end, repeated operation of the parking lever during parking on slopes and similar conditions may …
Vehicles equipped with an optional dealer-supplied cold-climate front brake cable may experience cable end breakage. The inner wire casting position at the cable end is improper, causing the cable end to fracture …
The connector design in the rear combination light bulb carrier is inadequate, causing contact failure due to vehicle vibration. When the light is illuminated in this state, the connector may overheat. Repeated …
The alternator harness routing in blood collection vehicles is improper. Vibration from driving may cause the harness to contact the exhaust gas recirculation (EGR) cooler. Continued use in this condition may result …
In the Keyless Operation System Control Unit (KOS ECU), a manufacturing defect in the internal reset IC may cause the reset IC to malfunction in extremely low temperatures, resulting in microcontroller shutdown …
Certain hybrid large-capacity transit buses have inverters with insufficient durability and reliability in their current conversion devices. Inverter failure may prevent the drive motor and auxiliary motor from operating, causing the hybrid …
The brake plate, a component of the braking system, has an improperly designed groove intended to prevent interference between the brake shoe and brake plate. Concentrated tensile and compressive forces during braking …
The brake plate, a component of the braking system, has an improperly designed groove intended to prevent interference between the brake shoe and brake plate. Tensile and compressive forces concentrate in the …
In the engine, an incorrect corrosion preventative was applied to the sealing bolts that restrict rocker arm shaft rotation. Engine heat causes the fastening torque to decrease, resulting in bolt loosening and …
In vehicles equipped with diesel turbo engines, some intercooler hoses connected to the throttle chamber have insufficient clamp fastening force. Continued use may cause the hose to become disconnected due to engine …
In the controller for the forward/reverse hydraulic clutch of the power transmission device, due to an inappropriate travel control program, unintended sharp turning may occur when left steering is immediately performed after …
Due to improper assembly procedures during wheel loader manufacturing, some rear axle trunnion fastening plate bolts are missing washers. Continued use in this condition may cause bolt torque to loosen, resulting in …
In the 7-speed DCT automatic transmission of hybrid vehicles, the sleeve does not move smoothly on the hub of the 1st gear inside the transmission. As a result, the 1st gear may …
The throttle pedal lever is made of inadequate material, and repeated operation may cause the lever to fracture and detach. If the throttle pedal lever detaches, the pedal cannot be depressed, preventing …
The pressure gauge displaying the internal pressure of the brake system pressure vessel does not indicate the minimum effective operating pressure of the equipment on its scale, failing to comply with safety …
The dashboard trim finishing work was not performed. In the event that the passenger seat airbag deployment is necessary, it may not deploy properly. Additionally, unexpected dashboard damage may occur during airbag …
In mechanical automatic transmissions for light-duty trucks and buses, internal cleaning during valve body manufacturing is inadequate, leaving foreign material in the hydraulic circuit. This can cause malfunction of the clutch control …
In hydraulic pumps driven by the engine via PTO (Power Take-Off) components, which supply hydraulic pressure to braking systems, power steering systems, and snow removal equipment, the hydraulic pump input shaft exceeds …
The control switches on the left and right sides of the steering wheel have inadequate design tolerance for thermal expansion and contraction of the internal circuit board, which may cause wiring fracture …
In vehicles equipped with a 7-speed S tronic automatic transmission, improper gear oil may cause an internal short circuit on the transmission control computer circuit board, resulting in the power supply fuse …
Vehicles equipped with a 7-speed DSG automatic transmission may experience internal short circuits on the transmission control computer circuit board due to improper gear oil, causing the power supply fuse to blow. …
The coating material on the terminal portion of lighting circuit fuses is inadequate. Vehicle vibration causes damage to the terminals, which combined with thermal effects generates non-conductive material (zinc oxide), resulting in …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.