In the planetary carrier of a road roller's reduction gear, the spring pin retaining hole for fixing the planetary pin that locks the planetary gear has a manufacturing defect. The spring pin …
住友 HN210WHH 2008
住友 HN215WHH 2008
住友 HW30VWH-2 2008
住友 HW41VWH-2 2008
日立 CC135C-3A 2008
+4 more
In the brake system piping, the oil return line connection from the brake valve is positioned improperly, which may allow air to enter the brake lines and reduce braking effectiveness.
Yanmar EG97 2011–2013
In vehicles where de-icing agent is applied, the air piping (nylon tube) for the rear axle parking brake (wheel parking brake) has insufficient strength. During snow road driving, snow adhering to the …
Hino Hino Ranger 2002–2012
In vehicles modified to double-cab configuration, sound-deadening material installed on the cab floor may sag due to cooling airflow during operation and contact the EGR cooler. The contacted sound-deadening material may become …
Isuzu Forward 2008–2010
On vehicles equipped with 18-inch wheels, if lug nuts are not reinstalled properly, the anti-loosening coating on the lug nuts may not provide adequate retention, causing lug nuts to loosen and generate …
キャデラック SRX 2012–2013
Due to manufacturing defects in the liftgate latch, internal component dimensions are inappropriate, causing the lock mechanism to fail to operate normally and the liftgate may not lock completely. In the worst …
Mazda Bongo 2012–2013
Nissan Vanette 2012–2013
The accelerator sensor, which detects accelerator pedal depression amount, may experience insufficient contact force in internal contacts when the pedal is depressed with lateral force applied, resulting in poor contact. This causes …
Nissan X-Trail 2004–2013
Nissan Serena 2004–2013
Nissan Fuga 2004–2013
Nissan Lafesta 2004–2013
Suzuki Landy 2004–2013
Improper welding of the wire and bolt inside the parking brake operating lever may cause the weld to separate with repeated parking brake operation, potentially resulting in parking brake failure.
アディバ CARGO3 2011
Certain airbag control units have insufficient electrical noise immunity. Consequently, noise generated by vehicle electrical components may damage the IC chip within the unit during use, and in worst-case scenarios, the airbag …
Honda MDX 2003
Certain child seats incompatible with the child seat detection system (a device that recognizes when a child seat is installed in the front passenger seat and prevents deployment of the front passenger …
Mercedes-Benz Duoplas 2011–2012
The resin bracket inside the fuel pump, when long-term immersed in test oil used during fuel pump manufacturing, undergoes non-uniform swelling due to glass fiber orientation effects when gasoline is subsequently supplied. …
Honda Cross Cub 110 2011–2013
Honda Super Cub 110 2011–2013
Honda Super Cub 110 MD 2011–2013
Honda Super Cub 110 PRO 2011–2013
Honda Super Cub 50 2011–2013
+2 more
On the front wheel brake, due to improper positioning of the inner wire casting at the cable end, repeated operation of the parking lever used for parking on slopes or inclines may …
Honda Super Cub 110 MD 2009–2012
Honda Super Cub 110 PRO 2009–2012
Due to improper engine control computer programming, insufficient intake air during deceleration from high engine RPM following throttle closure can result in unburned fuel being expelled and burned in the front catalytic …
Nissan Elgrand 2002–2006
The crankshaft position sensor has insufficient internal coil durability. Repeated high-engine-speed operation, such as wide-open throttle acceleration in low gears, applies excessive vibration to the sensor, potentially causing the coil to fracture. …
Daihatsu Atrai Wagon 2005–2010
Daihatsu Hijet 2005–2010
Daihatsu Hijet Deck Van 2005–2010
Subaru Dias 2005–2010
The crankshaft position sensor's internal coil has insufficient durability. When the engine is operated at high RPM repeatedly, such as full throttle acceleration in low gear, excessive vibration is applied to the …
Daihatsu Esse 2005–2010
Daihatsu Tanto 2005–2010
Daihatsu Tanto Exe 2005–2010
Daihatsu Mira 2005–2010
Daihatsu Mira Cocoa 2005–2010
+2 more
Due to improper machining work on the passenger-side dashboard, the airbag may not deploy properly when the airbag system detects a collision and activates. Additionally, unexpected dashboard damage may occur during airbag …
Mercedes-Benz A180 2012–2013
In drum-type brake systems, improper manufacturing of brake shoes results in insufficient adhesion between the lining and shoe. Repeated brake application causes the lining to separate, which can become wedged in the …
Yamaha Axis Street XC125E 2011
In the engine intake-side variable valve control device, large impact forces that rarely occur within the device after cold start can loosen bolts securing the device body. This may result in loss …
Lexus IS 350 2005–2011
Lexus IS 350C 2005–2011
Toyota GS350 2005–2011
Toyota Crown 2005–2011
Toyota Mark X 2005–2011
In the fuel filter attached to the asphalt finisher engine, the press-fit joint strength of the fuel line fitting on the upper side of the fuel filter may deteriorate due to vibration …
H A N T A F45W 2006–2013
H A N T A F45W3 2006–2013
住友 HA45W-7 2006–2013
The battery positive cable connecting the power distribution box and battery, which supplies power to the vehicle's electrical components, has improper plating metal and structure at the connector joint. Corrosion induced by …
BMW BMW 120i Cabriolet 2011
BMW BMW 120i Coupe 2011
BMW BMW 135i Coupe 2011
BMW BMW 320i Coupe 2011
BMW BMW 325i Coupe 2011
+2 more
In route buses equipped with a power transmission cut device (a structure that prevents power from being transmitted to the drivetrain unless the boarding/alighting door is closed), the electrical circuit for detecting …
Hino Hino Blue Ribbon II 2009–2013
Hino Hino Rainbow II 2009–2013
In route buses equipped with a power transmission cut device (a structure that prevents power transmission to the drive mechanism until the boarding/alighting door is closed), the electrical circuit for detecting the …
Isuzu Erga 2009–2013
Isuzu Erga Mio 2009–2013
In vehicles where the hill start assist (HSA) system has been relocated, improper positioning during reinstallation causes the HSA exhaust hose to interfere with bolts, resulting in hose deformation. Continued use in …
Isuzu GIGA 2010–2013
The hydraulic unit of the ABS (anti-lock braking system) may contain foreign material due to inadequate manufacturing processes, which in worst-case scenarios could prevent the ABS from operating properly.
Triumph Street Triple 2013
Due to improper manufacturing processes in the component production of the microcomputer power supply voltage monitoring circuit within the Electric Power Steering Control Unit (EPS ECU), some components exhibit defective characteristics. This …
Mitsubishi Outlander 2012–2013
Some vehicles have a clutch boss installed that differs from the manufacturer specification, resulting in insufficient fit with the main axle. Under load, this fit may disengage, preventing power transmission and causing …
Ｍｅｇｅｌｌｉ 250R 2011–2012
Improper mounting position and method of the rear brake hose may cause damage, resulting in brake fluid leakage and reduced braking force at the rear brake.
Ｍｅｇｅｌｌｉ 250R 2011–2012
The ECU program that determines rollover status using the bank angle sensor is inappropriate, which may cause the engine to shut down by incorrectly determining that the vehicle has overturned while in …
Ｍｅｇｅｌｌｉ 250R 2011–2012
During drive sprocket maintenance, over-tightening the mounting bolts can cause thread-locking compound to peel off. If the mounting bolts are reassembled without thread-locking compound, vibration may cause loosening and loss of drive …
Ｍｅｇｅｌｌｉ 250R 2011–2012
Some suspension link components (double connecting rods) that secure the rear suspension to the frame have inadequate durability due to improper manufacturing processes and materials. Consequently, the double connecting rods may fracture …
モト・グッツィ 1200 SPORT 4V 2012–2013