Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
10646 recalls on record · page 208 of 355
In the charging system, some current limiters (rectifiers) have resin with an insufficient proportion of curing agent. When temperature rises, this resin expands excessively, causing internal lead wires to fracture. This can …
The thrust collar for positioning the input shaft that transmits power from the engine to the slewing hydraulic transmission in the steering apparatus has insufficient strength. The thrust collar may break when …
Some vehicle frames lack welded reinforcement material. Continued use in this condition may cause partial frame breakage, and in worst cases, misalignment of the drive sprocket due to frame deformation, resulting in …
In the steering system, internal clutch components within the transmission that engage and disengage power to the left and right wheels may jam against each other, preventing clutch disengagement and making steering …
The cover of the pipe attached to the muffler's end plate has a structure that allows it to be easily removed from the noise prevention device.
1. The noise suppression device's muffler end plate has insufficient strength at the pipe attachment section. Vibration from the engine may cause cracks at this attachment point, risking fracture of the muffler …
On the axle of a vehicle-mounted trailer, slide shoes attached to the sliding portions of the axle extension section wear due to axle compression and extension during vehicle loading and unloading operations. …
Injuries — null The product poses a risk of injuries because there may be foreign material inside the brake tube which can potentially move into the brake master cylinder. If this occurs, …
The front fender mounting bolts have inadequate surface treatment on the threaded portion. When removed and reused during periodic inspections and maintenance, the bolts may loosen due to driving vibration and similar …
Some front wiper motors have deformed ground terminals. This can result in poor electrical contact at the ground terminal connection point, which may cause the front wipers to become inoperative.
The solenoid valve of the work implement control valve in the away-from-seat travel and load lock mechanism has insufficient water resistance. Rainwater and similar moisture may penetrate and cause short circuits. This …
In the steering system, the attachment method of the handlebar shaft mounting bracket to the frame is inadequate. When load is applied to the handlebar, the rubber mount may fracture and the …
Certain vehicle-mounted trailer axles have insufficient strength due to improper welding of the cylinder mounting boss for axle extension/contraction. Continued use in this condition may result in cracks developing at the boss …
In the rear suspension, the bush bracket connecting the rear lower arm and rear axle housing has limited strength margin. Repeated left/right turns and acceleration/braking cycles can cause the bush bracket to …
Front and rear wheel tires and wheels may have improperly assembled tubes that are pinched and damaged between the tire and rim. If the pinched tube becomes detached during operation, air may …
In the hydraulic power steering gearbox, improperly shaped cylinder pipes may have been installed, causing excessive load and damage to the O-rings attached to these pipes. This can result in power steering …
Medium-duty trucks compliant with 2010 emissions regulations may experience degraded nitrogen oxide (NOx) emission levels depending on driving conditions due to engine control program effects.
On small trucks with van or refrigerated unit bodies, the bellows tube of the exhaust gas recirculation (EGR) cooler has insufficient strength. Thermal expansion and contraction of exhaust gas can cause cracks …
In small trucks with manual transmissions, the backup light switch harness routing is improper; vibration of the harness mounting bracket causes the harness to bend and damage the insulation. Continued use in …
The tip-over engine shutoff sensor has an inadequate vibration isolation structure, which causes resonance at specific engine speeds. This can cause the sensor's internal tilt-sensing pendulum to shift into the tip-over detection …
In the brake piping between the brake master cylinder and brake actuator, internal cleaning during the manufacturing process was inadequate on some units, resulting in foreign material adhesion. This foreign material may …
In the electric power steering gearbox, repeated operation of turning the steering wheel fully to its extreme can cause the pinion shaft fixing nut to loosen. If use continues in this condition, …
The engine cooling electric fan blades are made of inappropriate material with insufficient strength, and some blades may develop cracks. Continued use can cause crack propagation and failure, and in the worst …
The handsfree unit programming in the electronic key locking system is inappropriate, creating a risk that the engine immobilizer may not reliably shut down engine operation.
Center lock wheel bolts have inappropriate fastening torque specifications, which may cause wheel and hub wear due to driving vibration and other factors. This can result in abnormal noise, and in worst …
Abnormal wear of the injector interior due to use of poor-quality fuel and similar causes increases fuel injection quantity, causing cracks and perforation in the piston. Combustion gas leaks into the crankcase …
In the rear-view mirror, the fixture used in the manufacturing process has minimal tolerance. Variations in polishing after cutting the reflective mirror result in some reflective mirrors having undersized dimensions. This may …
In the electrical wiring connected to the ECU, improper cable routing may cause the wiring to contact the frame pipe. Continued use in this condition can result in abrasion of the wire …
The electronic control unit (ECU) for fuel injection and the tilt sensor have insufficient waterproofing on the electrical wiring between the ECU and tilt sensor. Water may enter the electrical wiring during …
The fuel tank mounting structure is defective, causing a gap between the fuel tank and the vibration damper rubber, resulting in insufficient vibration isolation. Continued operation may cause cracks in the fuel …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.