Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
10646 recalls on record · page 290 of 355
The rear spindle has insufficient strength. Repeated sudden acceleration and similar operations may cause the spindle to fracture. This could result in rear wheel detachment and loss of vehicle mobility.
① The front spindle lacks sufficient strength. Repeated passage over steps and similar operations may cause the spindle to fracture. As a result, the front wheel may detach, rendering the vehicle inoperable.
In four-wheel drive vehicles, the front differential gear ratio is set improperly. Depending on rear tire wear conditions and load, when operating in four-wheel drive mode, torsional torque develops in the drivetrain …
On four-wheel-drive vehicles, the bearing press-fit section of the front-wheel knuckle has an improper structure. Mud and water accumulate in the press-fit section, causing the oil seal to wear and degrade in …
Certain check valve caps between the brake booster and intake manifold have improper welding, which may cause the check valve cap to detach due to engine vibration and similar conditions. This results …
The vent ring welded to the plastic fuel tank has improper molding. Due to repeated expansion and contraction of the fuel tank, cracks may develop in the vent ring. Consequently, when fuel …
Improper welding at the lower mounting point of the rear suspension shock absorber may cause the affected area to fracture due to vibration during operation, potentially resulting in loss of vehicle functionality.
The fuel filler pipe connector has been molded using an inappropriate method. Continued use may cause cracks to develop at the seam on the connector during molding, which in the worst case …
Front wheel spokes were improperly adjusted, resulting in non-uniform spoke tension during manufacturing. Repeated high loads during operation may cause spoke fracture. Continued use in this condition risks the broken spoke damaging …
Improper machining of the right-side rod in the power steering cylinder results in insufficient rod strength. Repeated steering operations may cause cracks to develop at the pin hole section of the rod. …
The rear combination lamp's red lens, which serves as both a tail light and brake light, has insufficient weather resistance. Prolonged exposure to strong sunlight causes the red color to gradually fade, …
The rear combination lamp's tail light and brake light dual-purpose red lens has insufficient weather resistance. Prolonged exposure to strong sunlight causes the lens red color to gradually fade, risking non-compliance with …
The wedge structure of the expander that extends the brake shoes in the primary braking system is defective. When brake linings wear beyond the service limit or shoe gap becomes excessive, the …
Due to inappropriate engine control unit programming, the throttle valve exhibits excessive amplitude in its closed position, which may cause the electronic throttle motor stopper to fracture. Consequently, engine control may enter …
The amber-colored coating material on the turn signal indicator bulb is inadequate, resulting in insufficient coating durability. Continued use in this condition may cause the amber coating to peel off, resulting in …
The air piping (nylon tubing) for the parking brake (wheel parking brake) is routed improperly, causing the nylon tubing to soften due to engine heat in some cases. As a result, the …
The tape wound between the bobbin and coil of the alternator has inappropriate material properties. Heat generated during power generation causes gas to be released from this tape, damaging the coil insulation …
The DPF (Diesel Particulate Filter) computer control program for automatic PM (particulate matter) removal is defective, preventing proper PM removal from the DPF. Excessive PM accumulation can cause the automatic regeneration function …
In vehicles modified to use compressed natural gas (CNG) in combination with gasoline fuel systems, the rubber hardness of the valve within the low-pressure regulator that controls CNG pressure and flow is …
In vehicles equipped with an aftermarket catalyst as a particulate matter reduction device, the joint structure connecting the exhaust pipe upstream of the catalyst to the catalyst is improperly designed, or the …
The float stopper structure in the brake fluid reservoir's brake fluid leak warning system is inadequate. During manufacturing, when brake fluid was pressurized and injected on the production line, the float became …
①The turbocharger impeller balancing process was performed improperly on some units, resulting in reduced blade strength. Consequently, partial blade loss can occur, causing output reduction. If operation continues in this condition, in …
The mounting bracket connecting the exhaust pipe and muffler has insufficient clamping force, which may allow exhaust gases to leak from the connection. Continued operation in this condition may result in the …
The ball joint nut fastening the knuckle and control arm has improper material composition, which may cause the nut to loosen due to vibration during operation. This generates abnormal noise, and if …
In independent suspension systems, the front suspension arm and rear suspension arm (on dual rear-axle vehicles) have insufficient rigidity. Road surface inputs during driving and braking inputs may cause cracking in the …
In the rear axle tube of low-floor, dual rear-axle heavy-duty trucks, improper die management during forging resulted in some vehicles being assembled with damaged tube components. Consequently, repeated input loads from road …
① In the ball joints of upper and lower arms on independent front suspension systems of small trucks, improper dust boot seal design allows mud and water ingress, causing wear of plastic …
In the ball joint of the tie rod end on small trucks with independent front axle suspension, the dust boot seal structure is inadequate. Mud and water can enter the joint, causing …
In police vehicle warning lights and sirens, the harness wiring has insufficient capacity. Prolonged use causes deterioration over time, resulting in oxidation on the harness connector terminals, which generates heat. If operation …
The relay rod of the steering apparatus has insufficient strength. Prolonged frequent use involving high steering forces, such as lock-to-lock steering operations, may cause cracks to develop. Continued use allows cracks to …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.