Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
10646 recalls on record · page 288 of 355
The attachment structure of the upper hinged door mounted on the vehicle rear is inappropriate. The resin hinges at the door upper edge deteriorate and fracture due to atmospheric ozone, ultraviolet light, …
In the braking system, brake shoe heat treatment is inadequate, resulting in insufficient adhesion between the brake shoe and lining in some units. Repeated brake operation may cause the lining to separate, …
Insufficient strength in the power steering cylinder anchor section. Repeated operation at maximum steering angle can cause cracks in this area. Continued use in this condition may result in anchor fracture and …
When an optional accessory cover is installed on the voltage regulator, the clearance between the cover and front fender is minimal. Under specific conditions where front suspension compression is at maximum, the …
Some forward-folding seats located adjacent to emergency exits on buses are not equipped with anti-tip brackets. Consequently, if a passenger falls backward against such a seat during hard braking, the hinge fastening …
The auxiliary steering system (device for ensuring operability when working with the driver's seat facing rearward) is prohibited for use during general road operation. Due to insufficient accidental operation prevention structure, if …
During fuel system hermeticity testing, some fuel tanks were deformed due to pressure exceeding the normal inspection pressure. As a result, when the vehicle is parked on a steep slope for an …
The rear number plate mounting bracket has insufficient strength, and cracks may develop in the bracket. Continued use could allow cracks to propagate, and in the worst case, the bracket could detach …
The notch groove strength in the rack that controls fuel injection quantity of the fuel injection pump is insufficient. Continued use at high RPM may cause the rack to fracture, resulting in …
Improper installation of the processor controlling turn signal and wiper signals, which is built into the steering column switch cluster, may cause intermittent signal loss, resulting in turn signals and wipers becoming …
The valve material and dimensions inside the ASR (Anti-Spin Regulator) valve, which prevents drive wheel slippage, are inappropriate. Consequently, the valve experiences age-related deterioration and deformation in high-temperature environments due to air …
The root of the rear hub flange lacks sufficient strength. Cracks may develop in this area following repeated high-frequency cornering operations. In early production vehicles, stress concentration due to combined factors such …
Due to insufficient fatigue strength margin in the front hub against maintenance conditions such as excessive tightening of hub bolts and operating conditions exceeding assumptions such as overloading, cracks may develop near …
The manufacturing method of the purge resonator, which reduces pulsation noise as fuel vapor passes through the hose, is improper. As a result, the welded joint of the purge resonator may separate. …
In the continuously variable transmission, some units have an incorrect component installed on the output pulley shaft. This causes the steel belt to interfere with a non-standard pulley contact area, risking damage …
The tie-rod attachment point on the steering knuckle has insufficient strength. Repeated lock-to-lock steering operations can cause cracks to develop at this attachment point. Continued use in this condition may result in …
Some window washer hoses installed inside the wiper arm are not properly fitted. Continued use may result in the hose becoming pinched by the spring inside the wiper arm. In the worst …
In the parking brake system, the anti-detachment structure between the parking brake spring and parking brake wire is inadequate, causing poor tracking between the spring and wire, resulting in wire slack. The …
The ultrasonic welding and lock pin securing the accelerator pedal cross-shaft to the throttle housing may be improperly installed. Continued use in this condition could cause the accelerator pedal to detach, potentially …
The auxiliary steering system (a device to ensure operability when working with the driver's seat facing rearward) is prohibited for use on public roads. Due to insufficient fail-safe mechanisms to prevent unintended …
The transmission steer pump drive unit has an inadequate structure, making it difficult to supply lubricating oil to the drive unit (drive sleeve section). Continued use may cause spline wear on the …
Due to improper programming in the engine control computer, the fuel injection shutoff function may not activate even when the steering lock mechanism is engaged. If the engine is started and the …
In the manufacturing process of the front seat belt retractor mechanism, improper installation of the belt retractor spring may prevent the seat belt from retracting properly. This could result in the inability …
The throttle cable in the acceleration system has inadequate water-resistant construction. Water splashed from the rear tire during wet-weather operation may enter inside the cable. At low temperatures, water that has entered …
The tape wound between the bobbin and coil of the alternator has inappropriate material properties. Heat generated during power generation causes gas to be released from this tape, damaging the coil insulation …
The washer at the side stand return spring hook pin fastening section of two-wheeled vehicles has insufficient strength. Spring tension during side stand operation may cause washer buckling, and repeated side stand …
The socket portion of the brake light and tail light bulb mounting base may be defective. Due to vibration and heat, the bulbs may loosen. Continued use in this condition may result …
The socket portion of the brake light and tail light bulb mounting board contains defective components. Vibration and heat may cause the brake light and tail light bulbs to loosen. Continued use …
The check valve (non-return valve) that prevents engine oil from flowing back from the cylinder head when the engine is stopped has an improper structure, causing inadequate fit and potential separation. Continued …
The outer covering of the front wheel brake cable on motorcycles is inadequate. In areas with tight cable routing, repeated flexing during cold conditions causes cracks in the outer covering, which tightens …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.