Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
10558 recalls on record · page 56 of 352
Medium trucks equipped with A05C (HC-SCR) engines may experience accumulation of sulfur components from exhaust gases on the HC-SCR catalyst due to an inappropriate regeneration control program. The catalyst fails to remove …
In child restraint systems, improper wiring attachment of the rear center seat belt buckle may cause wiring to interfere with ISOFIX attachment hooks. This may prevent the child restraint system from being …
On all-wheel-drive vehicles (snow removal trucks), the tail lamp harness was extended during rear modification, and the waterproofing at the connection was inadequate. Rainwater or snowmelt may penetrate the harness, causing corrosion …
The bipod strut connecting the lower rear suspension to the frame may have insufficient hardness due to improper manufacturing process. This component may fracture, causing the vehicle rear height to drop. In …
On small trucks, the passenger-side mirror may be equipped with a shorter-than-standard mirror stay due to improper design specifications. This may result in failure to meet the rear-view requirements of Safety Standard …
The relief valve regulating engine oil pressure has improper assembly, causing relief valve components to detach. This results in decreased engine oil pressure, illumination of the oil pressure warning light, inadequate engine …
Due to improper programming in the transmission control unit, when the Active Cruise Control (ACC) system is operating and the vehicle decelerates and stops upon approaching an obstacle, causing the engine to …
The secondary lock tab of the driver-side airbag connector was improperly installed during manufacturing, resulting in some units being installed in an incompletely locked state. This incomplete connection of the airbag connector …
Due to improper programming in the instrument module, when the ignition is turned on while internal temperature is below 0°C, an error message may display on the screen followed by a complete …
The resin grab bar mounted at the rear of the vehicle has improperly assembled fixed-mounting nuts that do not maintain required strength and proper fitment. When heavy loads are applied—such as when …
When wheel loaders are operated in cold environments, the engine oil separator may freeze internally. Continued operation causes engine oil to backflow into the combustion chamber, resulting in engine over-speed. This prevents …
(1) In the engine compartment wiring harness of agricultural tractors, improper routing causes contact between the wiring harness and the air conditioner condenser slide frame. Vibration during operation and friction with the …
(1) In agricultural tractor engine compartments, certain wire harnesses are routed improperly, causing contact between the wire harness and air conditioning condenser slide frame. Vibration during operation and friction with the slide …
(1) In agricultural tractor cabin front vibration damping material, improper assembly has resulted in sound-absorbing material being adhered over the protective film without removing the unnecessary protective film from the damping material …
(1) In agricultural tractor cabin front vibration damping material, improper assembly has resulted in cases where sound-absorbing material was adhered over the protective film without removing the unnecessary protective film from the …
In the steering system of agricultural tractors, the back pressure of the hydraulic circuit T-port is insufficient relative to the characteristics of the power steering controller. Under certain operating conditions, this can …
Due to improper programming in the seat belt reminder alarm, under certain conditions when a driver starts the vehicle without wearing the belt, only visual signals are displayed and the auditory signal …
The engine control program is improper, which may impair O2 sensor function due to high-temperature load operation or accumulated mileage. As a result, the engine check lamp may illuminate and exhaust emissions …
In the standing assist function, due to improper disk surface finishing, the caliper pads may adhere to the disk even when the assist is disengaged during acceleration, causing the self-support assistance to …
Due to improper programming in the engine control unit update software, the air-fuel ratio is not controlled correctly, and there is a risk that exhaust gas regulation values will not be satisfied.
In the power steering mechanism, some power steering motors were manufactured with improper settings on the production line, resulting in units that deviate from the standard specification. As a result, when the …
In recall notification No. 3218 (dated June 11, 2019), due to inadequate work instructions, wheel alignment adjustment may not have been performed after replacing the nuts that secure the rear suspension arm. …
The front radar sensor (FRS) electronic control unit has improper programming, which may prevent correct recognition under specific conditions, such as collision scenarios with bicycles traveling ahead. As a result, the collision …
On the relay emergency valve mounting area of dolly-equipped bunk trailers, insufficient structural strength causes cracks to develop in the reservoir-port side mounting socket attachment and service-port side pipe fittings due to …
The relay emergency valve mounting area on dolly-equipped bunk trailers has insufficient strength. Vibration during operation causes cracks to develop in the reservoir port side mount socket mounting area and the service …
On the axle spring seat of dolly-equipped bunk trailers, the shock absorber mounting bolt welds are improperly executed, resulting in insufficient strength in some units. This can cause cracking due to load …
In certain 2019 model year heavy-duty trucks equipped with 6R20 engines, the emission control system control module (ACM) has improper programming, resulting in incorrect fault diagnosis.
The electrical wiring of the horn lacks sufficient vibration resistance in the horn and bracket assemblies. Vibration of the vehicle body occurring within specific engine speed ranges causes stress on the terminal …
In the mirror glass of the passenger-side door mirror, improper process control during manufacturing has resulted in incorrect mirror glass being used in some units. The affected mirror glass has dimensions smaller …
The engine control unit program is inappropriate, so the engine warning light does not illuminate when components or systems malfunction. This does not comply with Safety Standard Article 31, Appendix 115 (technical …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.