1. In the brake cooling circuit, due to improper circuit design, hydraulic pressure in the circuit increases at low temperatures, which may damage the oil cooler. Continued operation in this condition may …
Komatsu FD35 2008–2011
Komatsu FD35N 2008–2011
Komatsu FD40 2008–2011
Komatsu FD40N 2008–2011
Komatsu FD45 2008–2011
+4 more
In the power steering cylinder of the steering apparatus, the coating on the cylinder rod end face is excessively thick. During tie-rod lock nut tightening, the coating is crushed, and if operation …
Yanmar EF326V 2008
Yanmar EF328V 2008
Yanmar EF330V 2008
Yanmar EF334V 2008
Yanmar EF338V 2008
+1 more
In side airbags, due to improper programming of the airbag control unit, the deployment signal may be incorrectly recognized during a side impact, causing the side airbag on the opposite side of …
Fiat 500 2010
Fiat 500C 2010
Fiat Abarth 500C 2010
Fiat Punto Evo 2010
During the welding process for the bracket that secures the steering apparatus to the vehicle body, prototype parts produced during production preparation were improperly handled and may have been mixed into production …
Toyota RAV4 2007
Toyota Vanguard 2007
In the heater circuit for heating intake air during cold engine starts, some vehicles have incorrect heater relay cable connections that bypass the fuse. If a short circuit occurs, excessive current flows …
Mitsubishi Mitsubishi Motor Grader 2011
In the intake air heating device that operates at low ambient temperatures, improper circuit design causes damage to the power supply circuit, allowing current to flow continuously. If use continues in this …
Mercedes-Benz Zetros 1833A 2009
In the fuel system of the combine harvester, improper fastening of the injection pipe may cause resonance during operation. This can result in cracks in the pipe, leading to fuel leakage and …
Kubota ER456 2008–2011
Kubota ER467 2008–2011
The dust cover installed on the engine compartment of street sweeper vehicles to prevent dust from being blown up during operation may accumulate soil and debris on top during cleaning work. The …
Isuzu Forward 1989–1999
In medium-duty trucks, due to improper tie-rod geometry, the front axle may contact the tie-rod when the steering wheel is turned to its maximum angle.
Isuzu Forward 2011
The fuel pressure sensor attached to the engine fuel supply rail may be insufficiently tightened, and engine vibration and similar factors can cause the fastening to loosen. This can result in fuel …
Nissan Juke 2010–2011
Nissan Serena 2010–2011
Suzuki Landy 2010–2011
On small high-floor dump trucks, the tailgate stopper was installed in an incorrect position to prevent interference between the tailgate and chassis frame, resulting in some vehicles not conforming to road transport …
Hino Dutro 2011
Isuzu Elf 2011
Mazda Titan 2011
Nissan Atlas 2011
In the braking system, improper assembly procedures of the brake light switch cause interference with the brake pedal in some vehicles. Continued use in this condition may result in braking force being …
Mazda Familia Van 2011
Mitsubishi Lancer Cargo 2011
Nissan AD 2011
Nissan AD EXPERT 2011
Nissan Wingroad 2011
The switch panel used during harvesting operations on combine harvesters has inadequate waterproofing around the volume control section. Prolonged water exposure can allow water to infiltrate inside the switch panel, causing corrosion …
ヰセキ HFZ585G 2009–2011
ヰセキ HFZ690G 2009–2011
ヰセキ HJ5120G 2009–2011
ヰセキ HJ6120G 2009–2011
ヰセキ HJ7120G 2009–2011
In the steering control system of combine harvesters, position sensors that detect steering lever position have wiring with insufficient slack in some units due to tight routing. Continued operation causes the wiring …
ヰセキ HJ5120G 2009–2011
ヰセキ HJ6120G 2009–2011
ヰセキ HJ7120G 2009–2011
The brake light switch has an improper internal structure. During braking operation, the spring that maintains contact pressure becomes energized and generates heat, causing the spring to elongate. If use continues in …
Suzuki Skywave 2010–2011
The design evaluation of the operating circuit for the electric auxiliary coolant pump that cools the turbocharger was insufficient. Continued use in this condition may cause metallic substances to form on the …
BMW MINI Clubman Cooper S 2006–2011
BMW MINI Cooper S 2006–2011
BMW MINI Cooper S Clubman 2006–2011
BMW MINI Cooper S JCW 2006–2011
BMW MINI Cooper S Convertible 2006–2011
+4 more
Injuries — null The affected vehicles may experience a problem related to the auxiliary belt and tensioner. If the tensioner failed, there would be a sudden loss of power assisted steering and …
Volvo Chassis numbers:V70: 000347 - 106435 S80: 000856 - 106230 XC60: 000229 - 028507 XC70: 000329 - 065138 Note: not all vehicles in the above chassis ranges are affect.....
In the air tank drain cock for the braking system, inadequate management of the machining tools for the drain pin has resulted in insufficient crimping and fixation of the drain pin O-ring. …
日通 - 2011
In the drain cock of the air tank for the braking system, inadequate management of the machining tool for the drain pin has resulted in insufficient crimping of the O-ring on the …
トレクス ― 2010–2011
In heavy-duty truck manual transmissions, improper fastening of the oil cooler hose allows debris picked up during operation to contact the hose, causing deformation and potential interference with the retarder drum (rotating …
ＵＤトラックス ― 2010–2011
Certain large trucks have improper fastening methods for the power steering high-pressure hose in the steering apparatus. Continued operation in this condition may cause hose damage, power steering oil leakage, and increased …
ＵＤトラックス ― 2010–2011
In the electrical system, the electrical wiring for the parking brake solenoid valve routed above the transmission is positioned in close proximity to the transmission. Due to vehicle vibration and other factors, …
T C M ZW100 2010–2011
T C M ZW120 2010–2011
日立 ZW100 2010–2011
日立 ZW120 2010–2011
Wiring for a fuel vapor canister purge valve, not used in Japanese-specification vehicles, is not secured to the vehicle body. During operation, vibration may cause the wiring and connectors to contact the …
Triumph Daytona 675 2010–2011
Triumph Daytona 675 R 2010–2011
In the steering system, improper manufacturing of the steering shaft mounting bracket may result in an inappropriate mounting angle of the steering shaft. When the steering tilt mechanism is adjusted to the …
その他 - 2003–2011
In large trucks, improper part number management of replacement airbag computers resulted in shipment of incorrect airbag computers. Vehicles equipped with incorrect airbag computers may experience delayed collision detection upon impact, potentially …
Hino Hino Profia 2003–2010
On vehicles equipped with a DPF (diesel particulate filter), the engine control computer has inappropriate idle speed during heater activation, causing black smoke and excessive PM (particulate matter) accumulation. This can result …
Isuzu Journey 2008–2011
Nissan Civilian 2008–2011
In vehicles equipped with DPF (Diesel Particulate Filter), the engine control computer has inappropriate operating conditions for automatic regeneration (combustion removal of collected particulate matter). This may cause frequent automatic regeneration during …
Isuzu Journey 2008–2011
Nissan Civilian 2008–2011
The door lock mechanism layout in the driver and front passenger doors is improper, which may allow water intrusion into the door lock assembly. If the door handle cable becomes water-soaked and …
Nissan Juke 2010–2011
In the turbocharger intake duct, improper machining of the turbocharger pressure sensor bracket welded joint results in insufficient weld strength in some units. Continued use in this condition may cause the turbocharger …
Nissan Juke 2010–2011
The rubber hose connected to the fuel tank internal pressure regulating valve is made of unsuitable material. Plasticizers leached from the rubber hose cause the valve internal component to swell, preventing proper …
Suzuki Escudo 2000–2005
Suzuki Grand Escudo 2000–2005