Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
5227 matching recalls · page 126 of 175
The fork bottom yoke that press-fits the steering shaft in the front fork has been manufactured improperly, which may cause cracks to develop in the yoke. Continued use in this condition can …
The valve material and dimensions inside the ASR (Anti-Spin Regulator) valve, which is installed to prevent drive-wheel slipping, are inappropriate. Due to aging caused by air pressure on the valve's rear surface …
On large buses equipped with a fluid retarder (auxiliary braking device), the propeller shaft connection (end yoke) structure is inadequate. The bearing retention stopper on the universal joint (spider) fitted to the …
The cooling hose of the fluid-type auxiliary brake device mounted on the transmission has insufficient durability. Cracks develop due to vibration during operation, and in some cases the hose becomes disconnected. Continued …
The mounting bracket supporting the cooling water hose for the fluid-type auxiliary brake system installed on the transmission has insufficient strength. Vibration during operation may cause the bracket to crack or break. …
An incorrect spacer bolt was installed on the travel spool of the transmission control valve. This causes improper spool stroke in some units. As a result, pressurized oil may flow into the …
The parking brake cable may be improperly assembled at manufacturing, causing interference with the rear wheel brake pipe. Continued use in this condition risks wear at the interference point.
Due to improper assembly instructions for the torque converter lubrication hose, the hose ferrule near the oil filter connection port is deformed in some units. Continued use may cause the rubber and …
Insufficient clearance between the tire sidewall and rear axle may cause the rear axle to interfere when the steering is operated to maximum lock angle. Continued use in this condition may damage …
The ABS (Anti-lock Braking System) unit installed in the engine room has an inappropriate control program that may fail to properly regulate rear-wheel braking force. If continued operation occurs in this state, …
The waterproof structure of the power steering electric hydraulic pump power connector is inadequate, allowing rainwater ingress at the connector. Continued operation can cause terminal corrosion, short-circuiting, and in worst case, fire.
In the transmission, the reverse microswitch contact capacity within the shift lever is inappropriate. When the lever is operated to the reverse position, instantaneous overcurrent can cause temporary contact welding. Consequently, even …
Injuries — This product poses a risk of injuries because brake lights may stay on, which may cause a road accident as the vehicle travelling behind an affected vehicle would not be …
The power steering hydraulic pump mounting structure is inadequate, causing the auxiliary drive belt tension to reduce the fastening force of the pump mounting bolts. Continued use may result in bolt fracture, …
The head height of the rear leaf spring center bolt is improper, causing the center bolt head to interfere with the rear axle, creating a gap between the spring and axle. This …
The sealing method for the fuel pump relay case is improper, causing sealant to adhere and bond to the wiring. Continued use may result in internal wiring disconnection due to thermal cycling …
On vehicles equipped with a turbocharger, the oil feed pipe that supplies oil to the turbocharger has inadequate corrosion and water resistance design. Repeated driving on roads where de-icing salt is applied …
A defective control board is installed in the cooling fan module motor. Even if coolant temperature rises, current may not flow to the cooling fan motor, preventing fan operation. Continued use may …
Improper plating of ECU (Engine Control Computer) electrode terminals causes oxidation and solder joint separation. Continued use results in electrode contact failure, warning light illumination, rough idling, and in worst case, engine …
The tilt angle sensor for the engine kill switch, which stops the engine when the vehicle tips over, is mounted in an improper position. Engine heat may cause internal components to deform. …
The electrical wiring for the horn is routed improperly, causing stress on the wiring during steering operations. Continued use may result in wiring damage, and in the worst case, an open circuit …
In the brake booster, the sprocket strength of the vacuum pump is insufficient, causing abnormal wear of the sprocket teeth. Continued operation may cause the vacuum pump chain to ride up on …
The lock device has improper press-fitting of the key cylinder cap retaining pin in some units, causing the pin to dislodge and the cap to separate. Continued operation may result in internal …
Fire — The dual mass flywheel may become damaged due to the configuration of the restrictor passage in the bleeder valve in the hydraulic pressure line for clutch actuation. This can happen …
In vehicles modified as car transporters, the bracket installed to relocate the brake air master lacks sufficient rigidity. Continued use may cause brake air pipes to vibrate and crack during operation, leading …
Fire, Injuries — The dual mass flywheel may become damaged due to the configuration of the restrictor passage in the bleeder valve in the hydraulic pressure line for clutch actuation. This can …
As standard equipment, the wheel covers mounted on the wheels are manufactured with a large outer diameter. For this reason, when the tire experiences significant load such as when riding up a …
In police vehicles, the resin band securing the battery cable has insufficient heat resistance. Due to heat in the engine compartment, the band may break. This causes the battery cable to sag …
The cable guide bracket of the parking brake pedal may have improper machining. As a result, when the brake pedal is operated, the bracket may deform, increasing the parking brake pedal travel, …
In vehicles modified to rail-road hybrid vehicles (rail-compatible vehicles, etc.), the steel brake air piping has an inappropriate shape, allowing water to accumulate inside the piping. Continued use may cause rust to …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.