Due to improper engine control unit software programming, the fuel pump may continue operating after the ignition switch is turned off. This can cause fuel to leak from the injectors and accumulate …
Peugeot Peugeot 307 XS 2001–2004
Peugeot Peugeot 307 XS Break 2001–2004
Peugeot Peugeot 406 Sport 2001–2004
Peugeot Peugeot 607 2001–2004
The flange section of the rear axle shaft has insufficient strength. When driving repeatedly at high speed on winding mountain roads and similar routes, cracks may develop at the base of the …
Toyota Land Cruiser Prado 1996–1999
The ball bearing case of the wheel-side joint on the front drive shaft has insufficient strength. Repeated full-lock steering maneuvers can cause cracks to develop in the case. If the vehicle continues …
Chrysler Grand Voyager 1998–2000
Chrysler Voyager 1998–2000
The brake pedal attachment point on the primary braking system has insufficient structural margin. When the pedal attachment area corrodes and wears due to de-icing agents or similar substances, the structural strength …
日立 LX70-5 1999–2003
日立 LX80-5 1999–2003
In front axle braking systems, improper welding instructions for air-over-hydraulic booster mounting brackets result in some units not being securely welded to the vehicle body. This causes the booster to vibrate excessively …
Isuzu Erga 2001–2005
The parking brake cable has an improper guide roller mounting structure, which increases sliding friction between the cable and guide roller during parking brake operation. Continued use may cause cable wear, and …
Mercedes-Benz 416CDI 2005
Due to improper handling during engine transportation, some units had their oil filler caps loosened during the process. Continued use in this condition may cause oil to spray from the cap area …
Mazda MPV 2006
The electronic fuel injection pump's overvoltage protection device has insufficient capacitor capacity. Continued operation in this condition may cause the capacitor to short-circuit due to overvoltage generated during engine start-up and similar …
キャタピラー 924G 2002–2005
キャタピラー 924GZ 2002–2005
キャタピラー 928G 2002–2005
In the anti-lock braking system (ABS), the foreign object intrusion prevention cover structure for the front-wheel rotation speed sensor is inadequate. Flying stones and similar debris can strike and deform the sensor. …
Isuzu Elf 2000–2002
The hose length of the rollover shutoff valve (front) installed to connect the left and right fuel tanks to the canister is inappropriate. Continued use may cause the hose to fracture due …
Ferrari 360Spider 2003
Some bolts fastening the horn switch to the steering wheel have insufficient strength. When the airbag deploys in extremely low temperatures, the pressure may fracture these bolts, causing the horn switch to …
Mazda Roadster 2005–2006
The ignition switch contact structure is inadequate. With extremely high switch usage frequency, wear particles generated during operation accumulate near the contacts and cause conductivity. Continued use may result in the starter …
Suzuki Every 1998–2000
Suzuki Carry 1998–2000
Suzuki Scrum 1998–2000
In ambulances, the rubber diaphragm in the brake booster has insufficient heat resistance. Thermal effects in the engine compartment may cause the diaphragm to thermally degrade and crack. Continued use risks crack …
Toyota Grand Hiace 1995–2005
Toyota Grand Hiace Van 1995–2005
Toyota Granvia 1995–2005
Toyota Granvia Van 1995–2005
Toyota Touring Hiace 1995–2005
+4 more
The carbon brush material in the fuel pump motor is inadequate, causing premature wear. Continued use allows wear to progress, and in the worst case, the fuel pump may become inoperable, resulting …
Volkswagen Passat 2.8 V6 4Motion 2002–2003
Volkswagen Passat Wagon 2.8 V6 4Motion 2002–2003
The motor within the fuel pump uses carbon brushes made of inappropriate material, causing premature wear in some units. Continued operation may accelerate wear, potentially resulting in fuel pump failure, engine stoppage, …
Audi Audi A4 1.8T Quattro 2002–2003
Audi Audi A4 3.0 quattro 2002–2003
Audi Audi A4 Avant 1.8T quattro 2002–2003
Audi Audi A4 Avant 3.0 quattro 2002–2003
Audi Audi A6 3.0 quattro 2002–2003
+1 more
During stabilizer link installation, inadequate work instructions have resulted in insufficient tightening of the attachment nut on some vehicles. Continued use in this condition may cause the nut to detach and the …
Mitsubishi Fuso Canter 2005
During rear axle manufacturing, improper assembly work has resulted in insufficient tightening of the wheel hub and trailing link assembly bolts. Continued use in this condition may cause the bolts to loosen, …
Mazda MPV 2006
On vehicles with axle suspension, the bracket securing the transmission shift cable has improper geometry, causing the cable to interfere with the power steering gearbox and become locally bent. Continued use in …
Mitsubishi Fuso Canter 1999–2002
The assembly process for the inflators of the side airbag, curtain shield airbag, and knee airbag was improper, resulting in insufficient gas heating agent charge in some units. Consequently, when subjected to …
Lexus GS350 2003–2005
Lexus GS 430 2003–2005
Lexus IS250 2003–2005
Lexus IS 350 2003–2005
Toyota Vitz 2003–2005
+5 more
In the accelerator that controls vehicle travel speed of electric forklifts, due to improper electrical circuitry, malfunction can occur due to electrical noise generated during steering operation. Therefore, when steering is performed …
小松 - 2003–2006
Injuries — A concern affecting the steering shaft of some Nissan Pathfinder R51 and Nissan Navara (D40) has been identified. The concern is related to the fitment of the lower steering shaft …
The side cover mounted on the right side of the engine compartment has an improper shape. During wet weather driving and similar conditions, water splashed up may contact the power steering pump …
Mitsubishi Chariot 1997–2003
The parking brake cable end fitting on the center brake side (cable end connector for securing to center brake lever) has an improper shape, which may cause the cable end to seat …
Mitsubishi Fuso Rosa 1995–2002
On vehicles equipped with ABS, damaged fixtures used during the installation of the wheel speed detection ring onto the front hub have caused scratches on the race of the front hub outer …
Isuzu Forward 2002–2004
The slide door front latch cover has an improper drainage position, allowing drained water to accumulate at the lower end of the outer handle cable. During outer handle operation, water droplets may …
Honda Elysion 2004–2006
Burns, Fire — There is a possibility that the filler tube may rust around the mounting bracket. This may create a small hole through progression of the rust, and fuel might leak …
On large all-wheel-drive vehicles, improper routing of electrical wiring within the left-side frame may cause interference with brake hose brackets or power steering oil pipes. Continued use in this condition may result …
Mitsubishi Fuso 2000
The bracket designed to prevent interference between the parking brake cable and transmission shift control rod has an improper shape. When the cabin is raised, the parking brake cable may become caught …
Mitsubishi Fuso Canter 1997–1999
Mitsubishi Fuso Canter Guts 1997–1999
The fastening structure of the rubber-equipped bracket securing the injection tube of the fuel injection pump is inadequate. When the bracket's rubber deteriorates, the mounting bolts and nuts loosen, potentially causing the …
Mitsubishi Fuso Fighter 2002–2004
The control program of the electronic control unit (ECU) governing the automatic transmission shifting is inappropriate. When the vehicle stops after driving in Drive range without depressing the clutch pedal, the clutch …
Mitsubishi Fuso 2000–2002