Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
5227 matching recalls · page 152 of 175
In the braking system, the front wheel brake hose is secured at an inappropriate position, causing the hose to twist. Steering generates excessive stress at the brake hose terminus. Continued use in …
In the lower arm (toe control link) sleeve of the rear suspension system, improper welding during steel tube material forming results in insufficient weld strength in some units. Continued use in this …
In the braking system, the return spring of the brake operating pedal is inappropriate. Repeated brake operations may cause the spring to fracture. If fractured, the brake light may illuminate even when …
In the steering system, the mounting bolts of hydraulic pipes in the gearbox are tightened to improper torque specifications. Vibrations during driving may cause these bolts to loosen. If operation continues in …
In the steering system, some steering gear boxes have improper welds at the mounting point. When performing lock-to-lock steering maneuvers during parking or similar operations, excessive loads are applied to this area, …
In the electrical system, improper routing of battery wiring within the right side frame may cause the wiring to interfere with clips securing the brake control nylon tube during vehicle vibration. Continued …
Interior door handles in seating devices have improper plating pre-treatment processing, resulting in residual plating solution trapped between the plating layer and resin. Continued use allows the residual solution to dissolve and …
In the steering system, the power steering hydraulic pump drive belt installation tension is excessive in some cases, which damages the pump bearing and causes hydraulic fluid leakage. Continued operation in this …
In wheelchair-accessible welfare vehicles, the tailpipe downstream of the main silencer has insufficient strength. Repeated extended idling operation can cause cracks to develop in the tailpipe flange. Continued use in this condition …
In the braking system, some vehicles have improper routing of the left front brake pipe, which can cause the pipe to interfere with the anti-roll bar link when the steering wheel is …
In the lighting system, the contact resistance capacity setting of the relay in the brake light electrical circuit is inappropriate. Repeated brake operations cause the contact surface to become rough, resulting in …
In vehicles equipped with front fog lamps, some fog lamp bulb sockets are improperly assembled. Vibration during driving may cause the bulb socket to detach from the fog lamp housing. Heat from …
In the braking system, the brake hose is improperly secured to the front strut area. During vehicle operation, vibrations may cause the brake hose to become dislodged from the retaining bracket. If …
In the power transmission device, the lock nuts fastening the bearings of the bevel pinions in the front differential have improper fastening torque and staking. Continued use in this condition may allow …
The brake system ABS control unit (ABS/ECU) connector interface with the vehicle wiring harness has incomplete waterproofing. Water intrusion at this joint can cause electrical short circuits, illuminating the ABS warning light …
In the braking system, some brake fluid has inappropriate viscosity. At low temperatures, brake fluid flow becomes sluggish, causing delayed brake engagement and release response when the brake pedal is operated, which …
The support bracket that secures the steering column shaft to the vehicle body has insufficient strength. Repeated abrupt steering wheel operations can cause cracks in the support bracket, resulting in unstable steering …
In the electrical system, improper routing of battery wiring within the right side frame may cause the wiring to interfere with the clip securing the brake control nylon tube due to vibration …
The intermediate arm shaft in the steering device linkage has insufficient strength, causing bending in some units. Continued use in this condition may result in bearing failure and, in the worst case, …
In the braking system, the rivet fastening method at the pivot point of the parking brake lever is improper. When the parking brake is operated, this area may twist, causing insufficient ratchet …
In the steering system, some vehicles have insufficient fastening torque on the bolt and nut that secure the right-side knuckle to the front strut. This can cause the bolt and nut to …
In the electrical system, V8 engine equipped vehicles have relay terminals for the low-pressure fuel pump drive circuit in the relay box made of inappropriate material. Engine compartment temperature rise and heat …
The adhesive securing the vibration-damping rubber on the crankshaft pulley that drives the accessory belt has insufficient heat resistance. At elevated temperatures during high-speed driving, adhesive bond strength deteriorates, causing the pulley …
In vehicles with automatic transmissions, the brake light switch electrical wiring circuit is improperly configured, causing the switch contacts to overheat and the resin component to melt. In the worst case, the …
In the steering system, some yokes connecting the steering column and gearbox have cracks due to improper heat treatment. Continued use in this condition may result in yoke failure, rendering the steering …
In the steering system, the steering shaft coupling joint is assembled in an improper position, resulting in the coupling not being fixed in the correct position. Continued use in this condition may …
In the powertrain system, the spring retaining position on the rod that locks the parking mechanism gear of the automatic transmission is inappropriate. Even when shifting to park position, the parking mechanism …
In the air heater that raises the temperature of intake air to the engine and improves cold-start performance, either ① insufficient waterproof and corrosion-resistant performance of the air heater relay, or ② …
Driver-side airbag inflator housings may have improper welds. During airbag deployment, partial housing fracture can occur, resulting in insufficient inflation gas supply and incomplete airbag deployment during collision. Additionally, fragments of the …
Due to improper machining of internal terminals in the vehicle speed sensor embedded within the left front wheel hub, vibration during operation may cause contact failure at the terminal section, preventing speed …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.