Before you buy, check it isn't under a dangerous recall.

The control program in the engine control unit immediately before vehicle stop is inappropriate, and there is a risk of engine stall immediately before vehicle stop in situations of high engine load, …

The oil filter housing in the oil filter module is made of inappropriate material, causing thermal expansion due to engine temperature. Repeated thermal expansion deforms the housing, compromising the seal integrity and …

Due to improper manufacturing processes within the fuel pump, plating coating on internal components may peel off and remain as foreign matter inside the pump. Continued use in this condition may cause …

In the fuel pump, improper manufacturing processes inside the pump cause plating coating on internal components to peel off and remain as foreign matter inside. Continued use in this condition may allow …

The power window switch in the driver's door has insufficient lubricating grease due to improper application method. Wear particles and moisture ingress from the terminal sliding contact form a short circuit, causing …

The vehicle body lacks sufficient structural strength at the hood latch mounting area. During high-speed driving with the hood primary lock disengaged, wind pressure and similar forces may cause deformation of the …

The driver-side airbag inflator may rupture during deployment, causing internal components to scatter and potentially injuring occupants.

Excessive grease was applied to the contact points inside the ignition switch. During switch operation, arc discharge heat causes the grease to carbonize and accumulate between the movable and fixed contacts, reducing …

The sealing ring material in the engine timing chain tensioner is inadequate, which may cause engine oil leakage. Continued operation in this condition may result in warning light illumination and engine damage. …

In braking systems equipped with a dual combined brake system that operates front and rear wheel brakes in coordination, the structure of the secondary master cylinder that transmits braking force from the …

Certain airbag control units have insufficient electrical noise immunity. Noise generated from vehicle electrical components may damage the IC chip within the unit during use, and in the worst case, could cause …

The control module circuit board that regulates the fuel pump may have foreign material adhered to it due to improper manufacturing. This can cause circuit short circuits, illuminating warning lights, and in …

The control program for the rear window defog device is inappropriate, causing continuous power supply in auto mode. This can cause the device to overheat, potentially resulting in fire.

In braking systems equipped with a dual combined brake system that synchronously operates front and rear wheel brakes, the secondary master cylinder structure that transmits braking force from front to rear wheels …

The fuel pump intake in the fuel tank has inadequate air-tightness in some units. This causes unstable fuel supply from the pump to the engine, resulting in rough engine acceleration and, in …

During correction work for handlebar peripheral component appearance defects, improper reinstallation of the handlebar holder has resulted in insufficient bolt torque on some units. Continued use in this condition may cause the …

In the system that alerts following vehicles via emergency flash lights and hazard warning lights during emergency braking or accidents, the control program is inappropriate, causing the hazard warning light flash frequency …

In fire truck (ladder truck) damping systems, improper welding between the rear-axle torque rod mounting bracket and frame undersurface can develop cracks at the weld due to repeated braking input. If use …

Variation in gas generator density was confirmed in certain driver-side SRS airbag inflators from recalled units. While the root cause remains undetermined, there is a potential risk that the airbag may not …

The driver-side SRS airbag inflator has inadequate moisture control after gas generant filling during manufacturing. This causes the gas generant to expand due to external temperature fluctuations during use, resulting in reduced …

The passenger-side airbag inflator may contain gas-generating material with insufficient density due to improper molding of the propellant or inadequate moisture prevention measures after molding. During airbag deployment, internal pressure in the …

In certain driver-side SRS airbag inflators, the container may rupture under internal pressure during airbag deployment, causing component fragments to scatter and potentially injuring occupants.

In the brake booster, the hose connection on the cabin side is positioned improperly, risking contact with the driver's foot. If this hose connection is pressed down forcefully, it may disconnect, causing …

The airbag control module contains an improperly coated circuit board. In high-humidity environments, the electrical circuit may corrode. Continued use risks circuit short circuits, illumination of the airbag warning lamp, and in …

Some alternators with insufficient generating capacity were installed during manufacturing. When high electrical loads are applied, such as during electric hydraulic power steering operation, the electrical load on the alternator causes internal …

Due to improper programming of the airbag control module, side curtain airbags and side airbags may inadvertently deploy when the vehicle tilts sharply left or right during driving.

The electric power steering control program is inappropriate. In cold conditions, the program may incorrectly determine a malfunction even when the electric power steering is operating normally. As a result, a warning …

On tank semi-trailers, improper process control of the welding between the suspension bracket cover plate and its reinforcing material results in insufficient metal penetration in some units. Consequently, running vibration and similar …

In tank semi-trailers, inadequate strength analysis of the frame (cross member) may result in cracking when excessive loads exceeding design values are applied during sharp turns. Continued use in this condition may …

In tank semi-trailers, insufficient weld strength in the reinforcement rib at the suspension bracket attachment point may cause cracks in the weld due to stress generated during braking. If use continues in …