Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
5188 matching recalls · page 99 of 173
The fuel pressure sensor attached to the engine fuel supply rail may be insufficiently tightened, and engine vibration and similar factors can cause the fastening to loosen. This can result in fuel …
On small high-floor dump trucks, the tailgate stopper was installed in an incorrect position to prevent interference between the tailgate and chassis frame, resulting in some vehicles not conforming to road transport …
In the braking system, improper assembly procedures of the brake light switch cause interference with the brake pedal in some vehicles. Continued use in this condition may result in braking force being …
The switch panel used during harvesting operations on combine harvesters has inadequate waterproofing around the volume control section. Prolonged water exposure can allow water to infiltrate inside the switch panel, causing corrosion …
In the steering control system of combine harvesters, position sensors that detect steering lever position have wiring with insufficient slack in some units due to tight routing. Continued operation causes the wiring …
The brake light switch has an improper internal structure. During braking operation, the spring that maintains contact pressure becomes energized and generates heat, causing the spring to elongate. If use continues in …
The design evaluation of the operating circuit for the electric auxiliary coolant pump that cools the turbocharger was insufficient. Continued use in this condition may cause metallic substances to form on the …
Injuries — null The affected vehicles may experience a problem related to the auxiliary belt and tensioner. If the tensioner failed, there would be a sudden loss of power assisted steering and …
In the air tank drain cock for the braking system, inadequate management of the machining tools for the drain pin has resulted in insufficient crimping and fixation of the drain pin O-ring. …
In the drain cock of the air tank for the braking system, inadequate management of the machining tool for the drain pin has resulted in insufficient crimping of the O-ring on the …
In heavy-duty truck manual transmissions, improper fastening of the oil cooler hose allows debris picked up during operation to contact the hose, causing deformation and potential interference with the retarder drum (rotating …
Certain large trucks have improper fastening methods for the power steering high-pressure hose in the steering apparatus. Continued operation in this condition may cause hose damage, power steering oil leakage, and increased …
In the electrical system, the electrical wiring for the parking brake solenoid valve routed above the transmission is positioned in close proximity to the transmission. Due to vehicle vibration and other factors, …
Wiring for a fuel vapor canister purge valve, not used in Japanese-specification vehicles, is not secured to the vehicle body. During operation, vibration may cause the wiring and connectors to contact the …
In the steering system, improper manufacturing of the steering shaft mounting bracket may result in an inappropriate mounting angle of the steering shaft. When the steering tilt mechanism is adjusted to the …
In large trucks, improper part number management of replacement airbag computers resulted in shipment of incorrect airbag computers. Vehicles equipped with incorrect airbag computers may experience delayed collision detection upon impact, potentially …
On vehicles equipped with a DPF (diesel particulate filter), the engine control computer has inappropriate idle speed during heater activation, causing black smoke and excessive PM (particulate matter) accumulation. This can result …
In vehicles equipped with DPF (Diesel Particulate Filter), the engine control computer has inappropriate operating conditions for automatic regeneration (combustion removal of collected particulate matter). This may cause frequent automatic regeneration during …
The door lock mechanism layout in the driver and front passenger doors is improper, which may allow water intrusion into the door lock assembly. If the door handle cable becomes water-soaked and …
In the turbocharger intake duct, improper machining of the turbocharger pressure sensor bracket welded joint results in insufficient weld strength in some units. Continued use in this condition may cause the turbocharger …
The rubber hose connected to the fuel tank internal pressure regulating valve is made of unsuitable material. Plasticizers leached from the rubber hose cause the valve internal component to swell, preventing proper …
In braking systems equipped with a dual combined brake system that allows front and rear wheel brakes to operate in coordination, the structure of the secondary master cylinder that transmits braking force …
The gas generant in the driver-side SRS airbag inflator contains defective material. If the airbag deploys, abnormal pressure rise within the inflator may rupture the container, scattering component fragments and potentially injuring …
The driver-side SRS airbag inflator contains defective gas propellant. Upon airbag deployment, abnormal pressure rise within the inflator may cause the container to rupture and scatter component fragments, potentially injuring occupants.
The design evaluation of the operating circuit for the electric auxiliary coolant pump that cools the turbocharger was insufficient. Continued use in this condition may cause metallic substances to be generated on …
Insufficient design evaluation of the operating circuit for the electric auxiliary coolant pump that cools the turbocharger. Continued use in this state may cause metallic substances to form on the circuit board, …
The design evaluation of the operating circuit for the electric auxiliary coolant pump that cools the turbocharger was insufficient. Continued use in this condition may cause metallic substances to form on the …
The pipe section of the power steering high-pressure hose may have an inadequately thin coating due to improper management of the plating process duration. Continued use in this condition can result in …
The attachment nut of the ball joint stud bolt connecting the front lower arm and knuckle arm of the suspension may loosen during use. Continued operation in this condition can result in …
The left and right rear brake hoses have been installed with improper pipe routing angles, causing some hoses to be positioned too close to the adjacent rear suspension springs. Continued use in …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.