Before you buy, check it isn't under a dangerous recall.

Front door latch and back door latch may have insufficient strength due to use of different material parts during manufacturing. Repeated lock and unlock operations may cause these components to fracture, resulting …

The fuel high-pressure pipe routing structure in agricultural tractor fuel systems is inadequate, causing cracks to develop at the high-pressure pipe attachment point due to engine vibration. Continued operation in this condition …

The horn bracket has insufficient strength. Vibrations generated at specific engine RPM ranges impose loads on the bracket, which may cause cracking. Continued use can lead to crack propagation, and in the …

Some fuel pumps have excessive crimping of wiring and terminals due to improper crimping work. This causes increased electrical resistance, leading to overheating of the affected area, melting of surrounding components, and …

In the fuel pump, the crimping of wiring and terminals is improper, resulting in some units being over-crimped. This causes increased electrical resistance, leading to overheating of the affected area and melting …

In shovel loader mufflers, the mounting bracket, fixing bolts, and engine-attached bracket have insufficient strength, which may cause fixing bolts to break or cracks to develop in the engine-attached bracket. Additionally, variations …

In the forklift rear axle bearing, improper bearing preload during assembly may cause spalling in part of the bearing. Continued operation in this condition risks rear hub bearing failure and tire separation …

In the rear shock absorber, improper welding at the mounting point may cause damage. This can result in abnormal noise and compromised driving stability.

Due to improper clearance design between the plastic impeller and fuel pump cover, the plastic impeller and fuel pump cover may interfere with each other as fuel temperature rises during operation. As …

On vehicles equipped with ABS, the mounting structure of the rear-wheel ABS sensor is inadequate, resulting in poor sealing at the mounting surface in some cases. Consequently, mud and water infiltrating through …

In direct-injection turbodiesel engines, the fuel injection pump seal may develop cracks due to improper manufacturing and design. If operation continues in this condition, cracks may propagate and eventually penetrate completely, potentially …

In the engine cooling fan drive HST (hydrostatic continuously variable transmission) of combine harvesters, the tension arm pivot pin manufacturing instructions are improper, causing some tension pulleys to be misaligned. Additionally, some …

In the fuel evaporative emission control system, improper coating application at the piping connection results in corrosion during use, potentially creating holes through which fuel evaporative emissions may leak.

The vehicle-side connector of the side and curtain airbag control module has some units with incorrectly arranged terminals. As a result, in the event of a collision, the seat belt pretensioner on …

Some large and medium-duty trucks have insufficient grease fill in the inner hub bearings. Continued operation in this condition may result in poor lubrication of the hub bearings, potentially leading to loss …

In the steering system, the intermediate shaft connecting the steering wheel and gearbox may have welding defects at the joint due to improper positioning of the welding equipment setup. Continued use in …

In the power transmission system of dual-axle rear-wheel-drive trucks, improper backlash settings between the spline section of the front flange of the rear-front axle final reducer and the spline shaft cause excessive …

The front right seat belt retractor may lock in low ambient temperatures due to improper manufacturing of retractor components, preventing the seat belt from being withdrawn and potentially leaving occupants unable to …

In the power transmission unit's hydraulic piping, the clamp securing the hydraulic hose has an inappropriate shape. Subjected to hydraulic pulsation vibration, the clamp and hydraulic hose may rub and sustain damage. …

In the hydraulic piping of the power transmission system: (1) The painting instructions for the mounting surface of the anti-rotation lock plate attached to the rotating joint are inadequate, resulting in insufficient …

In auxiliary brake lights, improper electrical circuit board design within LED elements may cause circuit board corrosion and loss of conductivity. Continued use may result in failure of the auxiliary brake light …

In large intercity buses, the control programs for the engine control unit and exhaust aftertreatment device control unit are inadequate, resulting in insufficient urea water injection quantity. This may cause nitrogen oxide …

On large tour buses, repeated prolonged flashing of the turn signal indicator can cause the orange cap on the rear turn signal indicator to melt. Continued use in this state may result …

In the manually retractable left-side mirror bracket of large tour buses, improper assembly results in weak axial tension on the mirror-side bracket mounting bolts. Vibration during operation can cause cracks to develop …

In light-duty trucks, the baffle plate (anti-slosh partition) welded inside the fuel tank lacks sufficient weld strength. Fuel sloshing causes the baffle plate to deflect, creating cracks at the spot welds. Continued …

In the steering column, the outer tube may have inadequate roundness, causing uneven load distribution on the inner bearings. Continued use may result in bearing damage, leading to increased vertical play in …

Improper IC manufacturing process control in the engine ECU may cause internal wiring fractures within the IC due to environmental temperature changes during use. This can result in abnormal fuel pump control, …

Due to improper programming of the electric power steering control computer, when a temporary battery voltage drop occurs during engine startup, power supply to the electric power steering may be shut off …

Due to improper programming in the lighting control computer, when the door is unlocked via remote control in low ambient temperatures, the answerback turn signal flash may be incorrectly identified as a …

Due to improper manufacturing of the acceleration sensor in the airbag control computer, self-diagnostics may detect an abnormality in the sensor. Consequently, the airbag warning light may illuminate and the front airbag, …