Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
10559 recalls on record · page 244 of 352
Improper assembly of the fuel hose to the fuel pipe may occur. In the worst case, the fuel hose may detach during operation, risking fuel leakage.
Incorrect replacement parts were supplied for the passenger-side airbag door in the airbag system, which may result in degraded airbag performance upon deployment.
Certain cylindrical flanges welded to the rear axle have improper welds that may develop cracks originating from the weld edge due to vibration during operation. Continued use allows cracks to propagate through …
On container semi-trailers, a spare tire carrier is mounted on the frame side between wheel bases. Vibration during operation may cause cracks to develop in the frame near the mounting area. Continued …
Improper fuel hose routing may cause interference with the engine cover during vehicle operation. Continued use in this condition risks fuel hose damage.
The attachment structure between the leaf spring and rear axle air spring is inadequate, causing fastener bolts to loosen during operation on rough roads and uneven surfaces. Continued use in this condition …
In the refrigerator installed in the living area of the camper vehicle, the gas piping of the propane gas cooling device is insufficiently secured. Vibration may cause cracks in the gas piping, …
In the travel motor hydraulic piping, due to inappropriate pipe geometry, the pipe vibrates during operation and cracks may develop at the pipe fitting joints. Continued operation in this condition may result …
Some crankshaft position sensors contain internal contamination. Continued use may prevent the sensor from properly detecting crankshaft position, potentially resulting in engine stall and inability to restart.
The water-sealing structure of the sliding contact area at the end of the automatic transmission control shaft is inadequate, which may cause corrosion during use. Continued operation in this condition can result …
The lower edge geometry of the glide-slide doors on low-floor transit buses is inadequate, creating a risk of foot injury if a door is actuated while a person inadvertently stands within the …
The lower edge geometry of the gliding slide-type door on low-floor transit buses is inadequate. If a person inadvertently enters the door operating range and the door is actuated, contact with the …
In large non-step transit buses, the reinforcement plate of the front right air spring bracket has an improper shape, and some units lack the required cutout. This can cause the torque rod …
In large non-step transit buses, the reinforcement plate of the front right air spring bracket has an inappropriate shape, with some lacking a notch. As a result, the torque rod may interfere …
The trailer hub may have insufficient strength due to casting defects occurring in the manufacturing process as a result of inadequate manufacturing control. Continued use may cause cracks to develop in the …
Certain combustion-type cabin heaters have improperly manufactured fuel pumps in the burner head (combustion unit). Continued use in this condition may cause fuel leakage from the fuel pump, which in the worst …
In engines equipped on refrigerated and frozen transport vehicles, the welding position of components constituting the tension pulley bracket for the refrigeration unit drive belt is improper, resulting in insufficient strength. The …
On large buses, the aerodynamic deflector panel attached to the vehicle body beside the right-side rear-view mirror has an improper shape, causing the overall width to exceed 2.5 meters.
The fuel pump control computer has insufficient water resistance, allowing moisture to infiltrate and corrode internal components. This may result in reduced fuel pump discharge pressure, and in worst case scenarios, engine …
On the work forward/reverse lever used during road cutting operations, there is insufficient clearance between the lever and the hydraulic hose of the road cutting device. If the road cutting device is …
In the side-impact airbag deployment control system, some vehicles have incorrect wiring of the pressure sensor that complements the acceleration sensor for detecting collision impact. As a result, side airbag deployment may …
Some welfare-equipped vehicles have an incorrect specification seat reinforcement bracket installed on the passenger-side slide-up seat (rotating lift seat). As a result, the seat may not be retained during a frontal collision, …
In low-floor four-wheel drive vehicles, insufficient exhaust pipe strength can cause cracking due to engine vibration. Continued use in this condition may result in exhaust gas leakage and, in worst cases, exceed …
The power supply tap point for the side turn signal indicator is improperly positioned, causing the current to exceed the flash control unit's rated capacity. Continued use may result in damage to …
Certain mechanical automatic transmission clutches have an improperly designed holder ring that connects the clutch release bearing and diaphragm spring, causing premature wear. Continued operation may result in the holder ring disengaging …
Certain clutch release bearings in the mechanical automatic transmission clutch actuation system have insufficient seal durability, causing grease leakage and inadequate lubrication, which may result in premature wear. Continued operation may cause …
The ABS control unit may experience corrosion due to de-icing salt, allowing water to infiltrate the unit interior. Continued operation may cause electrical circuit short-circuiting, potentially resulting in fire.
The ABS control unit may experience corrosion due to road salt exposure, allowing water to enter the unit interior. Continued use risks electrical short circuits, which could potentially lead to fire.
An oversized clamp was incorrectly installed at the fuel hose end. Continued use may cause the clamp's crimping force to decrease, potentially resulting in fuel leakage from the hose end in the …
In the front wheel assembly process, improper assembly work has resulted in insufficient fastening torque on the front wheel mounting bolts in some units. If operation continues in this condition, the bolts …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.