Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
5188 matching recalls · page 103 of 173
The fuel pump in the fuel tank may contain defective components. Continued use in this condition could result in pump failure, causing engine shutdown and inability to restart.
The cable end cover material in the front wheel brake is inappropriate. Repeated operation of the parking lever during parking on slopes or inclines may cause the inner wire to fracture, resulting …
In the backup alarm buzzer electrical wiring, the operating power source for the backup alarm buzzer and parking brake pressure switch are bundled together within the same harness. Electrical noise generated during …
In plug-in hybrid variants, the hybrid controller's fail-safe control program is inappropriate. If the brake position sensor malfunctions while engine controller and hybrid controller communication is impaired, the regenerative brake control fail-safe …
The brake hose located beneath the rider seat has minimal clearance between the seat backing and the hose. Operating vibrations and similar conditions may cause contact between the seat backing and brake …
On air suspension-equipped vehicles with large liquid transport tanks, the spare tire carrier mounting bracket installed between the rear chassis frames has insufficient durability. Vibration during operation may cause cracks in the …
In the steering mechanism, the assembly process of the steering shaft and steering upper joint is inadequate, resulting in some units where the fitting section between the steering shaft and steering upper …
In side airbags, due to inappropriate programming of the airbag control unit, the deployment signal may be erroneously recognized during a side impact, causing the side airbag on the opposite side of …
In the reducer that transmits power from the engine to the steering pump of the steering mechanism, the oil passage in the cover within the reducer is improperly designed, resulting in insufficient …
ABS control unit wiring is improperly routed and pinched between the battery tray or surrounding components. Continued operation may cause the wire insulation to abrade and short-circuit due to vibration during driving, …
In brake air hoses for heavy-duty trucks, improper mounting position of the hose causes it to become pinched between the air pipe clip fixing bolt and the protector. This can result in …
In the braking system, an incorrect component was installed in the master cylinder. When the brake pedal is depressed multiple times while the parking brake is engaged, pedal travel may increase. In …
In the brake caliper pad-to-disc clearance adjustment mechanism, improper component design allows the pad-to-disc gap to gradually narrow due to vibration during operation. Continued use may result in brake drag and smoking.
The steering valve in the steering apparatus lacks a safety valve. During operation, impacts can cause excessive hydraulic pressure in the steering cylinder, which may loosen the nut securing the cylinder rod …
In the engine, due to improper settings of the parts assembly equipment, the piston clip, which serves as a retaining ring for the piston pin that fastens the piston and connecting rod, …
The brake drum section of the front axle hub has insufficient strength and may fracture. Continued use in this condition could result in brake failure.
In vehicles equipped with a regenerative control-type DPF, the brake air tube, parking brake cable, and transmission cable routed near the exhaust pipe may reach high temperatures. Continued operation in this condition …
In the power steering system, the fluid return pipe may contact and chafe against the steering gearbox and other components due to driving vibrations, causing cracks in the return pipe and fluid …
In the wiring for left and right power sliding doors, insufficient securing of the wiring can cause the lower hinge of the power sliding door or the movable wiring case to contact …
In the air conditioning system, improper assembly positioning of the air conditioning housing creates gaps at the connection between the air conditioning housing and the air conditioning drain duct. Continued use may …
High-center-of-gravity vehicles have insufficient strength in the rear-axle air suspension stabilizer arm. Repeated rolling can cause cracks to develop in the arm. Continued use may result in arm fracture in the worst …
Some front axles have insufficient durability due to the use of defective material components for the planetary gear shaft. Continued use in this condition may cause wear of the shaft, resulting in …
Injuries — null The product poses a risk of injuries because the parking brake may not hold the vehicle stationary on a gradient as a result of oil contamination from the transfer …
In engines for medium-duty fire trucks, improper cleaning of internal gears has allowed foreign matter to enter the gear shaft bushings in some units. When fire equipment is operated, these bushings may …
The electrical control unit has inadequate waterproofing at solder joints during manufacturing. Water ingress can cause internal circuit short-circuiting. This prevents signal transmission to the engine control computer, which interprets this as …
Tractor front turning radius specifications were set incorrectly. Consequently, certain towed trailers may interfere with the tractor-side trailer control valve, causing air leakage from the trailer brake system. In the worst case, …
In the fuel pump, improper assembly of the fuel pump discharge nipple and fuel tube connector (quick connector) may result in the quick connector not being properly seated. This may cause the …
On vehicles equipped with truck-mounted cranes, the gap between the transmission crossmember and the crane-mounting bolts—through which the parking brake cable is routed—may be insufficient on some vehicles. As a result, the …
Due to improper positioning of the brake pedal link and brake light switch, the switch may fail to operate. As a result, the brake light may not turn off even when the …
During manufacturing of the brake booster, the internal diaphragm may be scratched. Continued use in this condition could cause the scratch to perforate, potentially resulting in reduced braking force in worst-case scenarios.
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.