Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
5227 matching recalls · page 127 of 175
In vehicles modified to rail-land hybrid vehicles, the clearance between the hydraulic system and frame for mounting the cargo bed and the brake air hose is inadequate. Vibration during operation may cause …
The air cleaner case is secured improperly. Due to vibration during operation, the brake pipe and air cleaner case fastener may interfere with each other. If operation continues in this condition, the …
The waterproof structure of the throttle position sensor connector is inadequate, allowing water to enter the connector interior and causing terminal corrosion in some units. Continued use results in poor contact between …
Certain rear axles have inadequate weld strength in the spindle section due to improper welding. Repeated operation on rough terrain can initiate cracks at the weld, which may propagate during continued use, …
Due to improper assembly procedures for the steering shaft, some units have defective fitting at the connection between the shaft serration section and the hydraulic steering pump shaft. Continued use in this …
Due to improper machining of the parking mechanism actuation lever in the automatic transmission (mechanism that mechanically locks the transmission output shaft), when the lever is operated to the parking position, it …
Defective control boards have been installed in the cooling fan. If coolant temperature rises, current may not flow to the cooling fan motor, preventing fan operation. Continued use risks engine overheating, control …
The primary brake system has an improperly configured pneumatic circuit. When the parking brake is operated while the primary brake is being applied, excessive load is placed on the slack adjuster. Continued …
Due to improper wiring method in the headlight socket, when rewiring is re-routed after headlight bulb replacement, the socket bulb contacts may develop poor contact. This can cause arc discharge at the …
The worm gear structure within the power sliding door release actuator (a device that electrically operates the door latches on the front and rear sides of the sliding door) is inadequately designed. …
Insufficient clearance between the voltage regulator mounted on the front frame and the front fender may result in interference between the regulator and fender when the front suspension is fully compressed. Continued …
Improper assembly of the drive shaft to the transmission results in shallow engagement between the shaft and side gear, with some units lacking proper retention clip installation. Repeated steering inputs may cause …
Improper assembly of the drive shaft to the transmission results in shallow engagement between the shaft and side gear, and some units lack secure installation of the retention clip. Repeated steering inputs …
In the travel motor of the hydrostatic transmission, improper hydraulic control causes temporary oil supply insufficiency to the travel motor when slowly releasing the accelerator pedal during operation or slightly depressing the …
Improper routing of ABS sensor electrical wiring causes interference between the wiring and brake air piping in some vehicles. Continued use in this condition may result in air piping damage and air …
Front hubs lack sufficient margin for design loads when subjected to conditions exceeding specifications, such as excessive wheel nut torque or overloading. This causes excessive stress at the hub flange root, potentially …
During front suspension manufacturing, improper assembly procedures result in insufficient fastener torque on the lower arm-to-ball joint attachment bolt. Continued operation risks bolt loosening and potential fracture, which could result in loss …
The integrated control unit (ICU) that controls the key interlock mechanism (prevents key removal except in AT P position) has an improper circuit design. When ignition is turned off, the circuit can …
The electrical circuit of the ABS (Anti-lock Braking System) control unit is defective. Under conditions of extremely low battery voltage, the unit may fail to accurately calculate vehicle speed. As a result, …
In the primary braking system, improper selection of brake hydraulic piping causes resonance due to vibration generated in the brake lining during braking. Continued use may result in cracks developing in the …
The work parking brake lever, which is used only during loading/unloading operations on trucks and has a function to return the main transmission lever to neutral, employs a friction plate of inappropriate …
Certain steering column combination switches have insufficient durability in the electrical wiring insulation for wiper and window washer operation. Continued use may result in premature insulation degradation and peeling. In worst cases, …
In vehicles equipped with a back-up warning device sold as a dealer-optional component, there are cases where the wiring connection of the interrupt terminal added to the vehicle's electrical wiring was incorrectly …
Inadequate manufacturing control of the rear hub has resulted in foreign material contamination during the manufacturing process, causing insufficient strength in some units. Continued use may lead to cracks developing in the …
Due to inadequate manufacturing control of the rear hub, foreign material has been introduced into the material during the manufacturing process, resulting in insufficient strength in some units. If use continues in …
The union bolt setting in the oil passage that lubricates the vacuum pump supplying negative pressure to the brake booster is inappropriate, resulting in insufficient lubricant supply to the vacuum pump in …
The handlebar lacks sufficient strength, and cracks may develop at the electrical wiring hole in the center of the handlebar. Continued use without repair allows cracks to propagate, potentially resulting in handlebar …
The grease applied to the speedometer cable has inappropriate composition, which may harden the covering material (PVC). Continued use can cause cracks in the covering, allowing water ingress during washing and similar …
Due to manufacturing tolerances in the tie rod of the steering apparatus, the tie rod end may interfere with the axle mounting seat on the vehicle frame during maximum steering operation.
Due to improper positioning of the tie rod in the steering apparatus, there is a risk of interference between the tie rod and front axle during maximum steering operation.
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.