Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
5188 matching recalls · page 131 of 173
The hose length of the rollover shutoff valve (front) installed to connect the left and right fuel tanks to the canister is inappropriate. Continued use may cause the hose to fracture due …
Some bolts fastening the horn switch to the steering wheel have insufficient strength. When the airbag deploys in extremely low temperatures, the pressure may fracture these bolts, causing the horn switch to …
The ignition switch contact structure is inadequate. With extremely high switch usage frequency, wear particles generated during operation accumulate near the contacts and cause conductivity. Continued use may result in the starter …
In ambulances, the rubber diaphragm in the brake booster has insufficient heat resistance. Thermal effects in the engine compartment may cause the diaphragm to thermally degrade and crack. Continued use risks crack …
The carbon brush material in the fuel pump motor is inadequate, causing premature wear. Continued use allows wear to progress, and in the worst case, the fuel pump may become inoperable, resulting …
The motor within the fuel pump uses carbon brushes made of inappropriate material, causing premature wear in some units. Continued operation may accelerate wear, potentially resulting in fuel pump failure, engine stoppage, …
During stabilizer link installation, inadequate work instructions have resulted in insufficient tightening of the attachment nut on some vehicles. Continued use in this condition may cause the nut to detach and the …
During rear axle manufacturing, improper assembly work has resulted in insufficient tightening of the wheel hub and trailing link assembly bolts. Continued use in this condition may cause the bolts to loosen, …
On vehicles with axle suspension, the bracket securing the transmission shift cable has improper geometry, causing the cable to interfere with the power steering gearbox and become locally bent. Continued use in …
The assembly process for the inflators of the side airbag, curtain shield airbag, and knee airbag was improper, resulting in insufficient gas heating agent charge in some units. Consequently, when subjected to …
In the accelerator that controls vehicle travel speed of electric forklifts, due to improper electrical circuitry, malfunction can occur due to electrical noise generated during steering operation. Therefore, when steering is performed …
Injuries — A concern affecting the steering shaft of some Nissan Pathfinder R51 and Nissan Navara (D40) has been identified. The concern is related to the fitment of the lower steering shaft …
The side cover mounted on the right side of the engine compartment has an improper shape. During wet weather driving and similar conditions, water splashed up may contact the power steering pump …
The parking brake cable end fitting on the center brake side (cable end connector for securing to center brake lever) has an improper shape, which may cause the cable end to seat …
On vehicles equipped with ABS, damaged fixtures used during the installation of the wheel speed detection ring onto the front hub have caused scratches on the race of the front hub outer …
The slide door front latch cover has an improper drainage position, allowing drained water to accumulate at the lower end of the outer handle cable. During outer handle operation, water droplets may …
Burns, Fire — There is a possibility that the filler tube may rust around the mounting bracket. This may create a small hole through progression of the rust, and fuel might leak …
On large all-wheel-drive vehicles, improper routing of electrical wiring within the left-side frame may cause interference with brake hose brackets or power steering oil pipes. Continued use in this condition may result …
The bracket designed to prevent interference between the parking brake cable and transmission shift control rod has an improper shape. When the cabin is raised, the parking brake cable may become caught …
The fastening structure of the rubber-equipped bracket securing the injection tube of the fuel injection pump is inadequate. When the bracket's rubber deteriorates, the mounting bolts and nuts loosen, potentially causing the …
The control program of the electronic control unit (ECU) governing the automatic transmission shifting is inappropriate. When the vehicle stops after driving in Drive range without depressing the clutch pedal, the clutch …
In large-capacity transit buses, the flywheel ring gear hardness and starter magnetic switch activation circuit wiring length are inappropriate. During start operation, the starter pinion may collide with the flywheel ring gear, …
The ball joint attachment bolts on the front and rear suspension arms are improperly tightened. Repeated severe driving such as circuit operation can cause the attachment bolts to loosen. Continued use may …
Improper machining during battery positive terminal manufacturing has caused cracks in the affected component, resulting in battery electrolyte leakage that may contact the right front wheel brake pipe. Continued operation in this …
Due to improper engine control unit software programming, the fuel pump may continue operating after the ignition switch is turned off. This can cause elevated fuel line pressure, potentially resulting in fuel …
The fuel pump impeller has an oversized outer diameter, causing it to swell from fuel absorption and thermal expansion at elevated fuel temperatures, resulting in interference with the impeller case. Continued operation …
On four-wheel drive vehicles, the weld between the coil spring seat (lower seat) of the rear suspension device and the rear axle beam is insufficient. Due to vibration during driving, the weld …
In vehicles modified as garbage trucks, the dump cylinder mounting position is inappropriate, causing the brake pipe mounting bracket on the rear differential or the brake pipe and mounting bracket to potentially …
The steering cylinder in the steering system has an improperly shaped piston seal. Repeated small steering corrections can cause this seal to deform. Continued operation in this condition may result in a …
The fuel tank mounting position is improper, so during high-speed driving, road debris may collide with the front of the fuel tank. If the debris has protrusions, it could pierce the tank, …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.