Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
5227 matching recalls · page 135 of 175
An incorrect component was installed in the connector portion of the electrical wiring connected to the hydraulic unit, allowing water to enter the hydraulic unit through the connector. Continued use may cause …
The slave lever bracket mounting section lacks sufficient strength. Repeated operations such as lock-to-lock steering can cause cracks to develop in this area. Continued use in this condition may allow cracks to …
The suspension fork fixing thread pin lacks sufficient strength. In the market, if the camber adjustment shim is installed incorrectly or the lower arm bushing is modified, the load on the pin …
The electrical wiring of the alternator is inadequately secured. Vibrations from the engine cause the wiring branches to interfere with each other near the branch points, resulting in insulation damage. Continued use …
The fuel delivery pump in the accumulator-type fuel injection system may have foreign material clogging the overflow valve due to inadequate cleanliness control during assembly and manufacturing processes. When operated in low-temperature …
In front-wheel brake chambers of vehicles equipped with full-air brakes, the seal guide that retains the air-tight seal has insufficient strength and may fracture due to vibration during braking. Fragments of the …
On two-wheeled vehicles, the pin securing the return spring of the side stand is not made of the specified material, resulting in insufficient strength in some cases. Repeated operation of the side …
① The rear wheel brake hose routing is improper, which may cause the hose to contact the drive chain during operation. Continued use in this condition may result in hose damage, brake …
The ball joint connecting the knuckle arm and steering cylinder in the steering system has insufficient strength. Frequent high-load steering operations, such as maximum articulation, can cause cracks to develop in the …
The ball joint attachment points connecting the knuckle arm to the steering cylinder or tie rod lack sufficient strength. Repeated excessive loads from work impacts cause the fastening nuts or bolts to …
In the primary braking system, insufficient bonding strength between the brake shoe and lining may cause cracking in the lining. If operation continues in this condition, the lining may separate, potentially resulting …
The chain in the secondary reduction gear (tandem drive unit) of the power transmission system has insufficient strength. Continuous operation of the primary brake causes brake lining temperature to rise and braking …
The ratchet mechanism of the parking brake contains improperly machined detent teeth that may slip, preventing the lever from being locked. Repeated use of the parking brake may result in complete loss …
The fuel line routing from the fuel tank to the engine is improper, causing the fuel line to interfere with the air conditioning duct in some vehicles. Continued use in this condition …
The EGR (exhaust gas recirculation) pipe lacks sufficient structural strength. Thermal expansion and contraction of the pipe due to exhaust heat and engine vibration may cause cracks to develop. Continued use in …
Some sensors within the airbag control unit have improper processing, which can cause electrical circuit short circuits. As a result, the airbag may suddenly deploy when the ignition switch is operated.
The check valve installed between the brake booster and intake manifold is made of inappropriate material. Under high ambient temperatures with repeated high-load operation, engine temperature rises and the check valve may …
During assembly of the parking brake lever, a washer was omitted inside the lever in some units, resulting in insufficient locking force on the block that secures the lever. Consequently, the parking …
The front wheel hub lacks sufficient strength and torsional rigidity. Repeated heavy braking during operation causes hub deformation with stress concentration at the spoke area, potentially resulting in spoke fracture. Continued use …
The attachment bolts securing the hydraulic power steering gearbox to the subframe are insufficiently torqued. Repeated stationary steering operations can cause these bolts to loosen. Continued use may result in bolt fracture, …
During assembly, improper brake fluid injection causes excessive force at the brake reservoir tank and brake master cylinder junction, causing the rubber seal at this junction to fold and leak fluid. Continued …
②In the front suspension system, lower arms manufactured through an improper forging process were installed, and some of these lower arms developed cracks in the ball joint socket area. As a result, …
The engine control computer program is inappropriate, causing the engine to remain at high RPM and continue running even after the vehicle is stopped. High temperatures develop beneath the vehicle floor, potentially …
Battery water-proofing measures are insufficient, allowing rainwater to contact the battery top surface. When the battery is replaced with a unit other than the factory-installed battery, rainwater may enter the battery interior …
On medium-sized all-wheel-drive vehicles, the front brake pipe fixing method is inadequate, causing the brake pipe to resonate and crack due to brake drum vibration during braking. Continued use in this condition …
Injuries — Risk of injury: Possible dislodgement of the rubber sealing boots protecting the steering tie rod, that can result in rapid wear and possible tie rod end separation with loss of …
The hood locking mechanism securing the hood to the vehicle body contains insufficiently welded strikers attached to the hood. Continued use in this condition may cause the striker weld to separate. If …
Fire — Risk of fire. The second heating system is inadvertently activated during a garage/dealer intervention on the heating system, the structure of the second heating system can overheat; burning smell and …
Some rear door exterior handle door-open levers have defective riveting at the pivot point. This causes the lever to not fully return when the door is closed, preventing the latch from securing …
The fastening torque specification for the front axle mounting bolts is inappropriate. Repeated loads during snow removal operations may cause bolt loosening. Additionally, on some vehicles, paint residue remained on the front …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.