Before you buy, check it isn't under a dangerous recall.

A defect in the gas generator of the passenger-side airbag deployment device may cause the airbag to deploy at a slower speed than intended during collision.

Some turn signal operation switch units located below the steering wheel are installed in a position deviating from the correct location. During steering wheel operation, the electrical wiring of the operation switch …

When driving on uneven road surfaces, excessive impact is transmitted from the road surface to the steering wheel, which in the worst case may cause loss of steering control and rollover.

Some units have insufficient lubricant (grease) fill in the ball joint portion of the Pitman arm within the steering apparatus. Continued use in this condition may cause wear at the ball joint, …

The left front wheel brake pipe is improperly mounted and may interfere with the shock absorber. Continued use in this condition risks damage to the brake pipe, potentially resulting in brake fluid …

In diesel vehicles, the electronically controlled fuel injection pump's solenoid valve coil wiring may have improper routing or welding defects. Continued use in this condition may cause the coil wiring to disconnect, …

Rear wheel brake pipes contact accelerator cables and other cables on the upper left front frame of some vehicles. Continued use in this condition may cause the brake pipes to be damaged …

Improper installation of the front brake hose may cause contact between the brake hose and the inside of the tire wheel when turning the steering wheel. This may damage the brake hose, …

Due to improper geometry of the fuel tank shield, upon impact from collision or similar event, the propeller shaft may crush the fuel tank, which in the worst case could result in …

The bulb failure check circuit for the brake fluid leak warning light is incorrectly wired, causing it not to illuminate when the ignition switch is turned on in some vehicles.

Some front axles lack a washer or retaining screw on the hub nut that secures the hub bearing. This can cause hub bearing looseness, potentially resulting in loss of vehicle mobility.

Due to defective attachment of the glass guide frame inside the driver's door, the door lock mechanism may have improper engagement. In the worst case, the door could open while the vehicle …

Defective installation of the glass guide frame inside the driver's door may result in poor engagement of the door lock mechanism, which in worst case could cause the door to open while …

In right-hand drive vehicles, due to an improper computer program in the airbag control unit, the airbag may deploy when excessive impact is applied to the steering wheel, such as striking it …

In right-hand drive vehicles, due to improper computer programming of the airbag control device, the airbag may deploy if an excessive impact is applied, such as striking the steering wheel forcefully.

Due to improper construction of the ignition switch (engine ignition switch), internal wear accumulates metal particles that can short-circuit, potentially leading to fire.

Due to improper design of the ignition switch, internal wear generates metal particles that accumulate inside the switch, potentially causing short circuits and fire.

The plastic retaining clip that rotates the steering wheel and airbag contact ring (a device that supplies power to the airbag during steering operation) together may break due to insufficient strength. As …

Certain fuel pipes and fittings located on the upper engine have manufacturing defects. Continued use in this condition may result in fuel leakage and, in worst cases, fire.

If debris enters inside the parking brake cable cover, the cable may not fully retract when the parking brake lever is released, causing the brake to remain engaged. This can damage the …

Some brake hoses attached to the left rear wheel disc brake are assembled in an improper position. The hose may interfere with the fuel tank mounting bracket due to vertical movement of …

The body attachment point of the front suspension system lacks sufficient strength. Repeated hard braking at high speed may cause cracks to develop in this area. Continued operation in this condition could …

The diaphragm in the traction control system switch (a device that prevents tire slippage on low-friction road surfaces) has insufficient durability. Continued use in this condition may result in brake fluid leakage …

Some vehicles have water drain holes beneath the left rear side panel sealed with sealant. Rainwater can accumulate inside the panel, causing corrosion on the fuel pump electrical connector terminals, resulting in …

The air bag deployment sensor is prone to react to instantaneous impacts. The air bag may deploy when the vehicle passes through deep depressions at high speed or when riding over obstacles …

The airbag deployment sensor is prone to react to momentary impacts. The airbag may deploy when passing through a deep depression at high speed or when driving over an obstacle on the …

Some vehicles have headlight and power window fuses installed in swapped positions. If wiring shorts, fire may occur before the fuse functions.

Due to inadequate engine control computer programming for ignition timing and related parameters, backfiring may occur during engine start. In the worst case, the intake manifold may rupture, potentially leading to fire.

The guide stay of the airbag wiring connector at the steering wheel has manufacturing defects. The guide stay may detach, causing poor contact of the connector. This may result in airbag failure …

The upper universal joint of the steering shaft in the steering system may contain cracks due to manufacturing defects. Continued use in this condition could result in loss of steering control.