Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
5227 matching recalls · page 65 of 175
In large and medium-sized transit buses, the routing of the driver's instrument panel wiring is improper, causing the wiring to interfere with the edges of the instrument panel. Continued use may result …
The high-mounted stop lamp structure is inadequate to accommodate expansion and contraction caused by temperature changes, potentially causing cracks at the lamp's welded joints. Continued use in this condition may allow rainwater …
In the side airbag igniter, due to incorrect configuration settings in the production equipment abnormality response program, some units have improper igniter composition ratios. As a result, the airbag may not deploy …
The exhaust pipe insulation is improperly secured, causing the insulation seams to separate due to heat exposure and leaving the high-temperature exhaust pipe exposed. Continued operation in this condition may allow combustible …
Some vehicles have fuel hoses installed improperly, causing contact with the fuel tank and engine. Continued use in this condition may damage the fuel hose, potentially resulting in fuel leakage and fire.
On tank semitrailers, incorrect numerical values are recorded in the braking force field of the data label relating to the braking system affixed to the vehicle body and instruction manual, resulting in …
On large truck brake pedals, the split pin securing the pedal shaft is improperly assembled. Brake pedal operation may cause the split pin to disengage from the shaft. Continued operation in this …
Certain vehicles have improperly welded joints on the rear suspension toe link damper. Continued use in this condition may result in weld fracture and loss of vehicle mobility.
The weatherproof cover at the fresh air intake of the air conditioning system is improperly installed, allowing rainwater to enter the blower motor housing. This causes corrosion of the blower motor shaft, …
The blower motor resistor controlling the air conditioning blower motor has inadequate design, which may prevent the fuse from blowing even when circuit current rises and causes overheating. This may result in …
Engine ground wire routing is improper, with some units in contact with the driveshaft. Continued operation in this condition may result in ground wire damage during driving, which in severe cases could …
In the manual parking brake of small trucks, the spring force of the lever holding mechanism is inappropriate. When the lever is pulled up, if the tooth tips of the holding mechanism …
Certain passenger-side airbag inflators have inadequate moisture protection of the gas generant. Repeated temperature cycling in high-humidity environments can degrade the gas generant, potentially causing the inflator container to rupture upon airbag …
Improper assembly of the accelerator pedal has resulted in incorrect accelerator pedals being installed on some vehicles. When the engine automatically starts while the vehicle is stationary with brake hold engaged, electromagnetic …
The airbag inflator units have defective igniter composition due to inadequate manufacturing control. The igniters are not mixed to specification, which may result in airbag non-deployment during collision, causing severe injury to …
In four-wheel drive vehicles equipped with Vehicle Stability Control (VSC), the brake control program is defective, preventing accurate vehicle speed calculation during tire slip. This can result in insufficient braking force. Consequently, …
The inflator (inflation device) for the front passenger airbag in small trucks has inadequate moisture prevention of the gas generant, which may degrade due to repeated temperature and humidity fluctuations. This could …
The inflator (inflation device) for the passenger seat airbag has inadequate moisture prevention of the gas generant, which may degrade due to repeated temperature and humidity fluctuations. Consequently, the inflator container may …
The inflator gas generant in the driver-side airbag has an inappropriate moisture absorption temperature, which may cause the gas generant to degrade due to repeated temperature and humidity fluctuations. As a result, …
The passenger airbag inflator lacks adequate moisture protection of the gas generant, causing degradation due to repeated temperature and humidity cycling. This may result in inflator container rupture during airbag deployment.
In the torque converter of the continuously variable transmission (CVT), improper manufacturing of the internal bearing results in an uneven sliding surface. During use, this unevenness causes abnormal wear and potential fracture …
The passenger-side airbag inflator lacks adequate moisture protection for its gas generant, causing degradation through repeated temperature and humidity cycles. This may result in inflator container rupture during airbag deployment.
The inflator (inflation device) for the passenger-side airbag has inadequate moisture prevention of the gas-generating agent, which may deteriorate due to repeated temperature and humidity cycles. This creates a risk of inflator …
The passenger-side airbag inflator lacks adequate moisture protection for its gas generant, which may degrade due to repeated temperature and humidity cycles. This can cause the inflator container to rupture during airbag …
The inflator for the passenger-side airbag has inadequate moisture protection of the gas generant, which may degrade due to repeated temperature and humidity cycling. As a result, the inflator container may rupture …
Due to improper manufacturing of the fuel supply pipe, the interior of the pipe at the connector coupling attachment point may be damaged. This can cause gaps at the connector coupling attachment, …
The transmission shift lever returns to the center position after selecting a shift position, preventing the driver from shifting to Park range even when attempting to do so before the vehicle stops. …
The inflator of the passenger front airbag may have an improperly formulated igniter due to inadequate manufacturing control. Consequently, the passenger front airbag may fail to deploy upon collision, potentially causing severe …
The lower handlebar holder on the steering device has insufficient application of threadlocker on the stud bolts. Additionally, due to improper paint specification on the holder seating surface, repeated heavy loads from …
Due to improper attachment of the engine to the vehicle body, the air conditioning hose may contact the heat shield of the exhaust pipe. This can cause the air conditioning hose to …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.