Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
5227 matching recalls · page 98 of 175
In light-duty trucks and buses, improper manufacturing of the buffer rubber that secures the return fuel hose to the engine block causes phthalates leached from the rubber to degrade the hose, leading …
In the electric power steering system, improper manufacturing of certain component parts on the control module circuit board causes circuit malfunction. In this case, a warning light (power assist reduction) illuminates and …
Certain large and medium-duty trucks are equipped with defective wheel bearings on the front axle. Continued use may result in play, and in the worst case, brake drag could occur, potentially leading …
Due to an inappropriate control program in the engine control unit (engine ECU), when operating the air conditioning while maneuvering the vehicle at very low speeds without depressing the accelerator pedal (e.g., …
In large tractors, improper manufacturing of the brake valve causes the plunger actuated by the brake pedal to have poor sliding due to misalignment. Continued operation in this condition results in poor …
On the front brake hose, improper assembly of the electrical wiring for the ABS wheel speed sensor results in insufficient clearance between the electrical wiring and front brake hose in some vehicles. …
In the electric power steering system, due to improper programming of the control controller, excessive current may flow to the power steering motor during steering operation. This may cause an error message …
The headlight and turn signal operation switches on the instrument panel are positioned more than 500 mm from the center of the steering wheel, failing to comply with safety standards.
The engine rotation sensor lacks sufficient heat resistance. Under high-load conditions, repeated thermal stress may cause the sensor to break. When breakage occurs, fail-safe control prevents stalling, but depending on driving conditions, …
The fuel injection pump of the engine has improper heat treatment of the delivery guide inside the delivery holder, causing initial cracks in the seal area in some units. Continued use in …
The turbocharger turbine has improper casting, resulting in insufficient durability. Continued operation in this condition may cause turbine failure, leading to engine malfunction and reduced output. In the worst case, engine oil …
In the fuel injection pump of the engine, improper heat treatment of the delivery guide inside the delivery holder has caused initial cracks in some seal sections. If use continues in this …
The delivery guide heat treatment inside the delivery holder of the engine fuel injection pump is inadequate, resulting in initial cracks in the seal section on some units. Continued use in this …
The delivery guide in the delivery holder of the engine fuel injection pump has undergone improper heat treatment, resulting in initial cracks at the seal section in some units. Continued use in …
In the fuel injection pump of the engine, improper heat treatment of the delivery guide inside the delivery holder has caused initial cracks in the seal portion on some units. If operation …
In the fuel injection pump of the engine, improper heat treatment of the delivery guide inside the delivery holder has caused initial cracks in the seal area on some units. Continued operation …
The nut securing the tie rod end and pivot in the steering system may have insufficient tightening. Continued use in this condition risks the nut loosening, causing abnormal noise, and in the …
On the driver's side door, the notch position for mounting the cable connecting the inner door handle and door latch is improper. When the door opening and door lock operations are performed …
Some units have insufficient strength in the rear axle housing of the running gear. Continued use in this condition may result in rear axle housing failure and loss of vehicle mobility.
In the engine fuel injection pump, improper heat treatment of the delivery guide inside the delivery holder has caused initial cracks in the seal section on some units. If operation continues in …
Injuries — null Due to a software error in the transmission control unit, if the vehicle is parked in reverse gear and the engine restarted and neutral or first gear is then …
In the front axle propeller shaft of all-wheel-drive vehicles, the water-sealing performance of the rear joint is inadequate. Water splashed during driving can enter the joint, causing lubrication failure. Continued operation may …
On turbocharged vehicles, the engine control electrical wiring routing in the engine compartment has insufficient clearance between the wiring and the thermostat fitting mounting bolt due to inappropriate wire length. Continued operation …
Some airbag control units have been flooded with water leaking from the air conditioning system drainage duct. Continued use may cause internal short circuits, illuminating the airbag warning light, and in worst …
The battery wiring for the work engine is insufficiently secured, causing interference between the chassis frame edge and the battery wiring in some vehicles. Continued use may result in damage to the …
Rear propeller shaft couplings sold as replacement parts were manufactured without meeting design specifications, causing premature coupling failure and vibration during operation. Continued driving while ignoring vibration may result in rear propeller …
In the charging system, the structural bonding between the internal element and circuit board in the current limiter (rectifier) is inadequate. When temperature rises, the resin inside the current limiter expands, causing …
The filter cover mounting bolts installed in the work/control hydraulic circuit of the rotary snow removal vehicle have insufficient strength. Continued use in this condition may cause bolt fracture and hydraulic fluid …
On the rear-rear axle of large cargo vehicles (rear-front single-drive three-axle configuration), some vehicles have insufficient strength margin for their operating environment, which may cause cracks to develop in the axle. If …
In turbocharged vehicles, the crankshaft angle sensor's internal coil has insufficient durability. Repeated high-speed driving immediately after engine start can cause excessive vibration, potentially breaking the coil. This may result in engine …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.