Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
10559 recalls on record · page 180 of 352
In route buses equipped with a power transmission cut device (a structure that prevents power transmission to the drive mechanism until the boarding/alighting door is closed), the electrical circuit for detecting the …
In large truck propeller shafts, the spline shaft dimensions are undersized, resulting in excessive clearance between the spline shaft and the mating flange. This causes excessive loading on the fastening bolts that …
The electric wheelchair securing device has an improper motor stop method during belt release, which can cause gear seizure when the motor stops. This may prevent the motor from operating when the …
In vehicles where the hill start assist (HSA) system has been relocated, improper positioning during reinstallation causes the HSA exhaust hose to interfere with bolts, resulting in hose deformation. Continued use in …
The hydraulic unit of the ABS (anti-lock braking system) may contain foreign material due to inadequate manufacturing processes, which in worst-case scenarios could prevent the ABS from operating properly.
Due to improper manufacturing processes in the component production of the microcomputer power supply voltage monitoring circuit within the Electric Power Steering Control Unit (EPS ECU), some components exhibit defective characteristics. This …
The wheel crane headlights may not comply with safety standards because the adjustment method for the headlight (low beam) direction during vehicle production was inadequate, causing adjustment values to fall outside the …
Improper cable tie installation securing the starter cable results in insufficient clearance between the starter cable and the exhaust temperature sensor muffler cover of the UDPC (Diesel Particulate Filter). Continued operation may …
Some vehicles have a clutch boss installed that differs from the manufacturer specification, resulting in insufficient fit with the main axle. Under load, this fit may disengage, preventing power transmission and causing …
Improper mounting position and method of the rear brake hose may cause damage, resulting in brake fluid leakage and reduced braking force at the rear brake.
The ECU program that determines rollover status using the bank angle sensor is inappropriate, which may cause the engine to shut down by incorrectly determining that the vehicle has overturned while in …
The injector connector material is inappropriate. If excessive force is applied during servicing or if it is not installed properly, it may become damaged and cause fuel leakage.
During drive sprocket maintenance, over-tightening the mounting bolts can cause thread-locking compound to peel off. If the mounting bolts are reassembled without thread-locking compound, vibration may cause loosening and loss of drive …
Some suspension link components (double connecting rods) that secure the rear suspension to the frame have inadequate durability due to improper manufacturing processes and materials. Consequently, the double connecting rods may fracture …
On forklifts equipped with two LPG cylinders, incorrect thread selection on the nipple at the pipe junction where LPG converges may result in insufficient thread sealing. Continued operation in this condition risks …
In large transit bus HEV vehicles, insufficient clearance between the intake hose and turbocharger causes the turbocharger's heat to harden the intake hose rubber. Continued operation in this condition may result in …
In medium-sized buses, the bolts securing the front door to the vehicle body are insufficiently torqued, which may cause them to loosen and detach, rendering the door inoperable.
In large buses, heater hose fixing clamps lack sufficient clamping force, allowing coolant flowing through the hose to seep in at the hose end. This coolant degrades the hose's reinforcement fibers. Continued …
In the power transmission system, the parking rod that locks the parking mechanism gear of the automatic transmission has improper assembly work, and the rod's retaining portion is damaged in some units. …
On route buses, the turbocompressor impeller lacks sufficient strength against fluctuations in turbocharger rotation. Repeated high engine RPM operations during acceleration can cause compressor impeller fracture. Continued operation may result in white …
On route buses, the turbocharger compressor impeller lacks sufficient strength against fluctuations in turbocharger rotation speed. Repeated high-RPM engine operation during acceleration can cause compressor impeller failure. Continued use may result in …
The engine air intake duct retaining clip may crack when excessive force is applied during clip removal. Reusing a cracked clip allows the crack to propagate, potentially causing clip failure during operation. …
The EGR (Exhaust Gas Recirculation) valve bushing seal structure at the valve shaft is inadequate, causing reduced sealing performance during valve shaft actuation. This allows exhaust gas to enter the motor. Abnormal …
Priming pumps in diesel engine vehicles may have elevated residual stress from molding. Ozone degradation during use can cause cracking. If use continues, cracks may propagate through the wall, leading to fuel …
The turn signal indicators mounted on the door have insufficient contact pressure between the bulb and socket terminals. Frequent door opening and closing while the turn signal is operating can cause the …
Due to improper software in the body electrical control unit, when attempting to start the engine, the unit may fail to transmit the signal necessary for engine starting even upon receiving the …
The horns on the left and right are mounted in improper positions, allowing water ingress through the horn openings, which may degrade sound quality or cause electrical circuit flooding, resulting in one …
In large truck air brake systems, the air tube above the DPF device lacks sufficient heat resistance. Exposure to DPF device heat can cause partial melting of the air tube, resulting in …
In air brake systems of large trucks, the reducing valve (a pressure-reducing valve that switches pressure between the air tank for 4-axle rear air suspension and the brake air tank) within the …
In air brake systems of large trucks and buses, the safety valve (which opens to reduce pressure when air lines become over-pressurized for protection) has insufficient air discharge capacity. When air lines …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.