Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
10646 recalls on record · page 179 of 355
In the BCM (Body Control Module) that controls the operation of electrical components, due to an improper circuit design, noise generated during door lock actuation damages the turn signal indicator element, causing …
On medium-sized buses, a label displaying the initial inclination specification value for the cutoff line of the low-beam headlamp (the light/dark boundary line used when adjusting the beam direction) was not affixed, …
On medium-sized buses, a label displaying the initial inclination specification value for the cutoff line (the light-dark boundary used when adjusting the beam direction) of the dipped beam headlamp was not affixed, …
Some units have insufficient strength at the flange weld of the exhaust pipe upstream of the muffler. Continued use may result in cracking and failure to meet noise emission standards.
On rear doors, the cable connecting the outside handle to the door lock mechanism may return slowly, causing the cable to fail to return fully to the lock position when the handle …
In vehicles equipped with ceramic disc rotors for rear-wheel braking, the bolts fastening the disc rotor to the bell housing are made of inappropriate material. When used in high-salinity environments, these bolts …
In vehicles equipped with ceramic disc rotors for front and rear wheel brakes, the bolts that attach the disc rotors to the bell housing are made of unsuitable material. When used in …
In vehicles equipped with ceramic disc rotors for front and rear wheel braking, the bolts fastening the disc rotors to the bell housing are made of inappropriate material. When used in high-salinity …
The crankshaft angle sensor's internal coil has insufficient durability at high temperatures. When the engine compartment becomes overheated due to climbing or traffic congestion, repeated high-RPM driving such as full throttle operation …
The CVT hydraulic control program is inappropriate. When the accelerator is depressed sharply in conjunction with shift operation, or when the ignition switch is turned off from high engine speed (such as …
Due to improper engine control unit programming, incorrect throttle position commands may be issued, causing the engine warning light to illuminate during operation and triggering fail-safe mode, resulting in delayed throttle response …
Improper gap clearance between the side member and front end cross member allows the accelerator cable to route through this gap. If the vehicle front is struck while the cable is routed …
Due to inadequate control programming in the secondary transmission control unit, when the control unit receives erroneous signals that may be generated upon internal component failure of the secondary transmission while the …
In the fuel tank, some fuel transfer pipes connecting the main tank and sub-tank have improper geometry, which may prevent fuel in the sub-tank from transferring to the main tank. As a …
Due to improper control programming in the airbag control unit, the vehicle state may not be properly detected during low-speed rollover, potentially preventing the seat belt pretensioners and side airbag curtains from …
Battery forks lift battery plugs have improper crimping of the battery plug terminals, which increases contact resistance at the crimped section. This increases heat generation under high load. If use continues in …
In the engine cooling system condenser tank (a device that separates air bubbles from coolant), when the engine operates at high RPM, the air-water separation function may not work properly, causing coolant …
In large and medium-duty trucks and buses, the piston structure within the parking brake hand control valve is inappropriate. Moisture contained in compressed air during use causes the piston length to increase, …
Air conditioning compressor pulleys have inadequate armature (friction disk connecting compressor to pulley) strength due to improper mold design during formation. During use, the armature may detach, causing air conditioning failure, and …
In high-specification ambulances, improper installation of the battery cable to the starter motor has caused the cable to be damaged by interference with the engine. Continued use may result in cable short-circuiting, …
An incorrect joint disc is installed in the coupling that connects the transmission to the propeller shaft. During operation, the joint disc may deform, generating abnormal noise. If the vehicle continues to …
The throttle pedal lever is made of inappropriate material. Repeated operation may cause the throttle pedal lever to fracture and detach. If the throttle pedal lever detaches, the throttle pedal cannot be …
In CVT and AT equipped vehicles, the fastening force of the bolts connecting the drive plate and torque converter is insufficient, causing the bolts to loosen and potentially detach. This results in …
Certain light alloy disk wheels in the running gear do not bear the required markings (vehicle manufacturer name or trademark) that certify compliance with the technical standards specified in the 'Light Alloy …
In the hydraulic hose of the shovel loader, the hose insertion into the hydraulic fluid tank was not properly performed during manufacturing, resulting in some hoses with improper insertion depth. Continued use …
In shovel loaders, the wire harness may have been clamped in an inappropriate position during manufacturing. If operation continues in this condition, the harness may be pulled and severed during steering operation, …
In shovel loader wire harnesses, when water accumulates inside the corrugated tube protecting the harness and thermal cycling is repeated, capillary action can cause water to migrate along the electrical wiring from …
The structure of the seat belt and seat frame attachment is inadequate, resulting in improper installation of the attachment bolts. Continued use in this condition may cause the bolts to loosen, and …
If the turbocharger is damaged by external factors, vibration in the muffler support bracket increases, which may cause the bracket to fracture. In such a condition, oil spray increases, and in the …
In vehicles equipped with 4B10 engines, improper engine ECU programming may result in insufficient intake air volume or lean air-fuel ratio during idling, potentially causing engine stall near idle speed.
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.