Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
10646 recalls on record · page 181 of 355
In the headlamp electrical wiring, the positive power line is connected to the headlamp body side. If the headlamp body coating peels and conducts with the vehicle body, a short circuit may …
In large trucks, improper engine control programming and exhaust gas recirculation (EGR) pipe structure cause frequent interruptions of automatic and manual regeneration of the diesel particulate filter (DPF) during stationary operation. This …
In large-capacity transit buses, improper engine control programming causes post-injection fuel from automatic DPR (diesel particulate filter) regeneration during idle to enter the EGR (exhaust gas recirculation) circuit. The fuel is cooled …
In the engine cooling system fan pulley of combine harvesters, defective units with insufficient bolt seat strength were introduced during manufacturing. The pulley may fracture, causing the cooling fan to stop operating. …
On large trucks equipped with wing roof van bodies, the routing of the hydraulic piping for wing roof operation above the left front wheel deviates from the blueprint specifications. Assembly variations result …
Certain units have an incorrect clutch plate installed in the hydraulic clutch system, which may result in difficulty disengaging the clutch, inability to shift gears, and in worst cases, risk of falling …
The master cylinder in the hydraulic clutch has an improper design that is prone to air entrainment. Additionally, some units have incorrect clutch plates installed, resulting in difficult clutch disengagement, inability to …
Wire harnesses routed along body flex sections have improperly sized clamp holes, preventing adequate clearance between the harness and clamp. This compromises harness mobility during body flexing. Continued use may cause the …
During brake fluid refilling repair work, improper air bleeding of the brake lines has left air trapped in the brake hydraulic unit in some vehicles. This causes increased brake pedal stroke and, …
The distance between the edge of the flange securing the water pump pulley and the inner bend of the pulley is insufficient, causing the flange to ride up on the inner bend …
In the planetary carrier of a road roller's reduction gear, the spring pin retaining hole for fixing the planetary pin that locks the planetary gear has a manufacturing defect. The spring pin …
In the brake system piping, the oil return line connection from the brake valve is positioned improperly, which may allow air to enter the brake lines and reduce braking effectiveness.
The bolts, nuts used for fastening the reducer and drive shaft, and the front-axle-side spacer material are unsuitable. Proper fastening force cannot be achieved with the torque specification for the material used. …
The constant velocity joint of the propeller shaft between the engine and transmission was not manufactured correctly during production. Continued use in this condition may cause the constant velocity joint to fail, …
In the hydraulic pump that operates the hydrostatic transmission, the rear pump fastening bolts were tightened with excessive torque during hydraulic pump assembly, potentially causing deformation of the threaded holes. As a …
In vehicles where de-icing agent is applied, the air piping (nylon tube) for the rear axle parking brake (wheel parking brake) has insufficient strength. During snow road driving, snow adhering to the …
On continuously variable transmission (CVT) select levers, the fitting surface with the select button has been worn due to inappropriate tooling in the skin-forming equipment. During select button operation, the fitting may …
In vehicles modified to double-cab configuration, sound-deadening material installed on the cab floor may sag due to cooling airflow during operation and contact the EGR cooler. The contacted sound-deadening material may become …
Some stabilizer arms have insufficient strength due to improper heat treatment. Continued use in this condition may result in stabilizer arm fracture, compromised driving stability, and loss of vehicle control.
On vehicles equipped with 18-inch wheels, if lug nuts are not reinstalled properly, the anti-loosening coating on the lug nuts may not provide adequate retention, causing lug nuts to loosen and generate …
Due to manufacturing defects in the liftgate latch, internal component dimensions are inappropriate, causing the lock mechanism to fail to operate normally and the liftgate may not lock completely. In the worst …
In the automatic transmission of small buses, improper machining of the snap ring mounting location that secures clutch components may cause the snap ring to disengage, preventing torque transmission through the clutch …
Some stabilizer arms have insufficient strength due to improper heat treatment. Continued use in this condition may result in stabilizer arm fracture, loss of driving stability, and inability to continue operation.
The accelerator sensor, which detects accelerator pedal depression amount, may experience insufficient contact force in internal contacts when the pedal is depressed with lateral force applied, resulting in poor contact. This causes …
The side stand fixing bolt, which secures the side stand to the vehicle body and side stand switch, may loosen due to vibration. As a result, the side stand switch may fail …
The side stand switch fastening method is inadequate, which may cause the fastening to loosen and the switch to become slack. Consequently, the engine cut-off function that should activate when the side …
The luggage rack holder on dealer-optional luggage cases has an improper shape, which can cause bolts fastening the luggage rack and holder to loosen due to driving vibrations. Continued operation in this …
Due to improper engine control unit software, the exhaust gas recirculation (EGR) valve does not open properly. As a result, nitrogen oxide emissions exceed regulatory limits.
In the final reduction gear on the rear front axle of low-floor, dual rear-axle drive heavy-duty trucks, excessive play in the spline section of the front flange can cause excessive input to …
Improper welding of the wire and bolt inside the parking brake operating lever may cause the weld to separate with repeated parking brake operation, potentially resulting in parking brake failure.
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.