Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
5227 matching recalls · page 110 of 175
On the rear-rear axle of large cargo vehicles (rear-front 1-axle drive, 3-axle configuration), some vehicles have insufficient strength margin for their operating environment, which may cause cracks to develop in the axle. …
Incorrect fastening nuts were installed on the linkage connecting the front suspension stabilizer and strut. Due to vibration during driving, these nuts may loosen, causing abnormal noise, and in the worst case, …
In the power transmission system of agricultural tractors, an incorrect part was installed as the fixed nut of the axle clutch, which may cause the nut to loosen. This may result in …
The rear brake light switch has inadequate water-resistant construction. The switch reaches high temperatures from heat exposure near the catalytic converter, and when cooled by water ingress, moisture is drawn in through …
The ball serving as the fulcrum for the rocker cam that controls hydraulic fluid flow in the steering system hydraulic pump has insufficient wear resistance. Consequently, the ball may wear, and continued …
The heating elements (seat heater elements) in the driver and passenger seat heaters have insufficient durability. During prolonged use, cracks may develop in the heating film. This causes changes in electrical resistance …
In vehicles equipped with the optional SRS side and curtain airbags, the bracket securing the curtain airbag to the vehicle body may not be properly fixed. As a result, the airbag may …
The valve material and dimensions inside the ASR (Anti-Spin Regulator) valve, which is installed to prevent drive wheel slippage, are inappropriate. Due to aging from air pressure acting on the valve's rear …
In the acceleration control device, machining oil from the molding process adheres to a disk within the mechanism that regulates pedal operating force. During use, friction between the disk and plate gradually …
In the steering system, the assembly process for the screw that fixes the power steering hydraulic pipe to the steering gearbox was improper, resulting in some screws not being installed correctly. This …
The fuel return hose from the engine to the fuel tank was assembled incorrectly. During use, this hose may become damaged, causing fuel leakage, which in the worst case could lead to …
Some vehicles have insufficient tightening of the fastening bolts on the universal joint connecting the steering shaft and gearbox. When full-lock steering maneuvers are performed, these bolts may loosen, causing abnormal noise …
In high-specification ambulances equipped with an idle-hold device, improper connection of the electrical wiring for the idle-hold device may cause poor contact at the wiring joint. In the worst case, this may …
The shape of the lower switch housing that retains the throttle grip is inappropriate, and when assembled to the upper switch housing, the groove width that retains the throttle grip becomes narrower …
The rear-mounted air spoiler has insufficient structural strength at the rear attachment point. Cracks may develop at this attachment point due to vibrations during luggage door opening/closing or vehicle operation. Continued use …
Due to improper crimping of the pin securing the parking brake lever and ratchet, the ratchet may become immobile midway during parking brake operation. This can result in the parking brake lever …
On vehicles equipped with a simple cooling box, the high-mounted stop lamp wiring routing is improper, and the wiring insulation may be damaged during cooling box assembly. As a result, vibration during …
In the power control controller of electric forklifts, the internal electrical circuit is improperly designed, which may cause excessive voltage to develop within the circuit. As a result, internal components of the …
The retaining plate bolts on the right-side drive shaft bearing may loosen due to insufficient fastening torque. Continued operation may result in abnormal noise and slight vibration from the drive shaft during …
In the brake master cylinder, the inner seal may be installed in reverse orientation, resulting in insufficient sealing in some units. This can cause brake hydraulic pressure to decrease, potentially extending braking …
The steering wheel airbag inflator wiring harness routing is improper, causing the wiring to abrade and become damaged where it contacts the steering wheel bracket. Continued use in this condition may result …
During engine manufacturing inspection, inspection electrical wiring terminals were deformed, resulting in some engine-side electrical wiring terminals being deformed. Continued use in this condition may cause poor contact in the wiring, and …
The external air intake structure is inadequate, allowing rainwater to enter the blower fan motor section. This causes the motor bearings to rust and seize, resulting in blower fan motor stoppage and …
Incorrect assembly of wiring connecting the SCCM (Steering Column Control Module) equipped on the steering column and the driver-side airbag module may prevent the driver-side airbag from deploying as designed during a …
The center clip of the A-pillar trim was assembled with an incorrect part, resulting in insufficient retention force in some vehicles. In the event of airbag deployment due to an accident, the …
Inadequate waterproofing of the ABS control unit allows moisture containing de-icing agents to infiltrate the unit's terminal section, causing short circuits between terminals. This results in ABS function failure, with risk of …
Fire — The product poses a risk of fire because, under severe operating conditions, water may enter the driver’s window and reach the master power window switch, potentially causing the window switch’s …
The driver-side SRS airbag inflator contains defective gas generant. Upon airbag deployment, abnormal pressure rise inside the inflator may rupture the container, causing component fragments to scatter and potentially injuring occupants.
The driver-side SRS airbag inflator contains defective gas-generating material. Upon airbag deployment, abnormal pressure rise within the inflator may rupture the container, causing component fragments to scatter and potentially injure occupants.
ABS (anti-lock braking system) control program defect causes braking force to decrease after ABS activation compared to force immediately before activation. When ABS activates while braking on frozen or uneven surfaces, this …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.