Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
5227 matching recalls · page 113 of 175
On the front axle of forklifts, the seal structure of the parking brake mounting section is inadequate, which may cause lubricating oil to leak. Leaked lubricating oil may enter the parking brake, …
The brake accumulator (pressure reservoir) is secured using an improper fixing method. Vibration and similar conditions may cause cracks to develop in the brake piping connected to the accumulator. As a result, …
In electro-hydraulic power steering systems, improper manufacturing processes in high-pressure piping have caused internal rust formation in some units. This rust damages the bearing portions of the pump gear, increasing sliding resistance. …
The fuse for the engine ECU is shared with the fuse for the brake booster vacuum pump. If overcurrent occurs when the pump operates, the shared fuse may blow. This can cut …
The strut plate that holds the front wheel coil spring has insufficient strength. Repeated stop-and-go driving in hot, humid environments can cause cracks to develop in the plate, resulting in abnormal noise. …
In hybrid buses, the body frame shape is improper, causing interference with the fuel piping in some units. Continued use in this condition may result in fuel piping damage and fuel leakage.
The front brake reservoir tank has insufficient vibration evaluation near the engine's maximum rpm. During extended continuous operation near maximum engine rpm, vehicle vibration may cause air bubbles to form in the …
The check valve of the fuel evaporative emission control device has insufficient durability, and cracks may develop during prolonged use. If operation continues in this condition, fuel evaporative gas may leak into …
The fuel pump upper component is made of inappropriate material. Due to aging and operational environment exposure, cracks may develop in the pipe section within the upper flange of the pump. In …
The contact layout between the brake pedal and brake light switch is improper, which may cause the internal contacts of the switch to fracture. As a result, the brake light may fail …
① The tie rod adjust sleeve has improper machining and surface treatment, which can cause thread damage and loose fitting. If use continues in this condition, the tie rod end may disengage …
Trailer axles have insufficient penetration in welding due to inadequate process control in the automated welding equipment used to manufacture the axles. In some vehicles, this results in incomplete weld fusion. Cracks …
Trailer axles manufactured using automated welding equipment with insufficient process control exhibit inadequate weld penetration in some vehicles. This can cause cracks to develop in the affected axles. Continued operation may lead …
Trailer axles have insufficient process control in the automated welding equipment used to manufacture the axles, resulting in incomplete weld penetration in some vehicles. This can cause cracks to develop in the …
Trailer axles manufactured using an automatic welding machine with insufficient process control exhibit inadequate weld penetration in some vehicles. This can cause cracks to develop in the affected axles. Continued operation in …
The rear brake pipe located under the floor in front of the right rear wheel has an improperly shaped sound insulation material on the underside of the underbody cover, which can allow …
Some axle shafts have inadequate strength due to improper heat treatment. Continued use may result in shaft fracture in the worst case, leading to loss of driving capability.
In work lights (non-driving lights) used while driving, due to incorrect wiring diagram instructions in the electrical circuit, the work lights illuminate simultaneously when the headlights are turned on.
1. Rear axle mounting bracket has insufficient rigidity. Bracket deflection during excavation operations can cause bracket cracking or rear axle mounting bolt fracture. Continued operation in this condition may result in rear …
The rear axle mounting bracket has insufficient rigidity. During excavation operations, bracket deflection can cause bracket cracking and failure of rear axle mounting bolts. Continued use in this condition may result in …
Injuries — Possible corrosion of the brake pipes could lead to failure of one or both brake circuits and hence reduced braking performance or complete loss of braking.
Injuries — The product poses a risk of injuries because the fuel pressure regulator may become detached from the spigot within the fuel pump at high ambient temperatures. This would lead to …
In the potentiometer that measures brake pedal depression, the mounting shaft support method is inadequate, causing the shaft to not move smoothly in some units. If operation continues in this condition, the …
The front brake caliper piston has insufficient length. As brake pads wear, piston protrusion increases, reducing the engagement depth between piston and piston seal, potentially causing brake fluid to seep out. Continued …
Some medium-duty trucks with the front axle are equipped with incorrect brake pipes. If used in this condition, brake fluid may seep out in the worst case, reducing fluid volume and potentially …
In the wiring for side airbags and seatbelt pretensioners, improper crimping between connector terminals and wiring may result in insufficient contact between the terminal and wiring. If contact failure occurs, the airbag …
The driver-side SRS airbag inflator contains an improper gas propellant. If the airbag deploys, abnormal pressure rise in the inflator may rupture the container, causing component fragments to scatter and potentially injure …
In the wiring for side airbag/seat belt pretensioner, improper crimping between connector terminals and wiring may result in insufficient contact between the terminal and wiring. If contact failure occurs, the airbag warning …
In recall service operations for recall notices 2229 and 2294, the tightening torque specification in the fuel low-pressure pipe replacement service manual is inappropriate, which may result in insufficient clamping force on …
The mounting bolts for the power steering cylinder fixing pin in the steering system may have insufficient tightening torque. Continued use in this condition may cause the bolts to loosen and the …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.