The auxiliary steering system (a device to ensure operability when working with the driver's seat facing rearward) is prohibited for use on public roads. Due to insufficient fail-safe mechanisms to prevent unintended …
タダノ TR-100M 1983–1998
タダノ TR-160M 1983–1998
タダノ TR-200M 1983–1998
タダノ TR-250M 1983–1998
タダノ TR-350M 1983–1998
+3 more
The transmission steer pump drive unit has an inadequate structure, making it difficult to supply lubricating oil to the drive unit (drive sleeve section). Continued use may cause spline wear on the …
T C M L32 2002–2004
T C M L35 2002–2004
古河 FL345 2002–2004
古河 FL355 2002–2004
日立 LX160 2002–2004
+1 more
Due to improper programming in the engine control computer, the fuel injection shutoff function may not activate even when the steering lock mechanism is engaged. If the engine is started and the …
Chevrolet Corvette 1997–2003
The washer at the side stand return spring hook pin fastening section of two-wheeled vehicles has insufficient strength. Spring tension during side stand operation may cause washer buckling, and repeated side stand …
Honda VTX 2001
The socket portion of the brake light and tail light bulb mounting base may be defective. Due to vibration and heat, the bulbs may loosen. Continued use in this condition may result …
Chevrolet TrailBlazer 2002–2003
The socket portion of the brake light and tail light bulb mounting board contains defective components. Vibration and heat may cause the brake light and tail light bulbs to loosen. Continued use …
Chevrolet TrailBlazer 2001–2003
The outer covering of the front wheel brake cable on motorcycles is inadequate. In areas with tight cable routing, repeated flexing during cold conditions causes cracks in the outer covering, which tightens …
Honda Gyro UP 1999–2004
Improper clearance setting between the left front wheel brake pipe and the power steering hose retaining plastic clip can result in insufficient clearance due to assembly variation. During vehicle operation, vibration may …
Mitsubishi RVR 1991–1992
Mitsubishi RVR 1991–1992
Mitsubishi Chariot 1991–1992
The knuckle arm in the steering system has insufficient strength. Frequent prolonged use involving high steering force, such as lock-to-lock steering, may cause cracks in the knuckle arm. If use continues in …
Mazda Titan 1990–1991
The ball joint connecting the drag link and knuckle arm in the steering apparatus has insufficient strength. Frequent and prolonged use involving high steering force, such as lock-to-lock steering, may cause cracks …
Mazda Titan 1985–1995
In aerial work platforms, improper installation of the exhaust pipe has caused gaps in the clamp tabs on some units. Continued use may cause the clamp bolt to fracture and the exhaust …
Isuzu Elf 1998–1999
Some airbag control units have fine cracks in the solder joints of the circuit board. Vibrations during driving may cause these cracks to propagate, resulting in circuit discontinuity. Depending on the location …
Mazda Axela 2004
During axle assembly, some vehicles have improper lock nut tightening on the front wheel hub outer bearing, and insufficient grease fill between the front wheel hub outer bearing and hub body. As …
Hino KL-HU2PMEA 2000
Due to improper machining of the axle shaft spline, engagement between the axle shaft spline and the differential side gear may be insufficient in some units. Continued use in this condition may …
Hino KC-FD1JJCA 1997–2001
Hino KC-RJ1JGAA 1997–2001
Hino KC-RJ1JJAA 1997–2001
Hino KC-RJ1JJCA 1997–2001
Hino KC-RJ1JJCK 1997–2001
+16 more
The nylon tube material of the fuel pipe is unsuitable, causing cracks to develop in the tube over time. As a result, fuel may spray from the pipe, which in the worst …
キャデラック Eldorado Touring Coupe 1994–1997
キャデラック Concours 1994–1997
キャデラック Seville Touring Sedan 1994–1997
The waterproof structure and heat-resistance temperature rating of the air-conditioning harness fuse terminal are inadequately specified. When rainwater enters the air-conditioning fuse holder, the fuse terminals corrode, increasing contact resistance. Heat generated …
Suzuki Escudo 1988–1995
In the power steering mechanism, hydraulic piping routing is improper. When the steering wheel is turned to its maximum angle, the piping may interfere with the link rod. Additionally, vibration during driving …
Isuzu GIGA 2004
During axle assembly, some units have improper lock nut tightening on the front wheel hub outer bearing area, and some have insufficient grease fill between the front wheel hub outer bearing area …
Isuzu Forward 2000–2004
Insufficient removal of foreign matter during electric fuel pump manufacturing can damage wiring insulation on the internal motor, causing short circuits. This may blow the fuel pump circuit fuse or cause abnormal …
Toyota Sienta 1999–2004
①The contact point geometry of the brake light switch is inadequate for the electrical load applied to it, which can cause oxide formation on the contact surfaces and increased contact resistance. This …
Toyota Wish 1999–2004
Toyota Vitz 1999–2004
Toyota Estima L 1999–2004
Toyota Corolla Fielder 1999–2004
Toyota Sienta 1999–2004
+2 more
The right rod of the power steering cylinder was processed improperly, resulting in insufficient strength. Repeated steering operations can cause cracks to develop in the pin hole area of the rod. Continued …
小松 - 2002–2003
The feed hose length of the hydraulic power steering system is inappropriate. When the steering wheel is quickly returned from full lock, hydraulic pressure fluctuates sharply at the valve that switches oil …
Honda Legend 2004
Improper assembly of the fuel line quick connector fitting has resulted in insufficient engagement of some quick connectors. Continued use may cause the quick connector to shift under fuel pressure, compromising the …
Honda Inspire 2003
The bearings of the brake hydraulic pump drive gear mounted inside the engine have improper machining, which may cause the bearings to wear rapidly. If operation continues in this condition, the brake …
キャタピラー 924G 2003–2004
キャタピラー 924GZ 2003–2004
キャタピラー 928G 2003–2004
In the brake hydraulic pump, the fixing method for the pressure adjustment screw of the control valve is inadequate, which may cause the nut securing the screw to loosen. Continued operation in …
キャタピラー 924G 2002–2004
キャタピラー 924GZ 2002–2004
キャタピラー 928G 2002–2004
The castle nut fastening torque for the ball joint connection of the tie rod linking the rear axle center arm and knuckle is insufficient. Repeated steering inputs can cause the castle nut …
T C M FD35T9 2004
T C M FD50T9 2004
T C M FG40T9 2004
Certain check valve caps between the brake booster and intake manifold have improper welding, which may cause the check valve cap to detach due to engine vibration and similar conditions. This results …
Volvo Volvo S40 2003–2004
Volvo Volvo V40 2003–2004
The vent ring welded to the plastic fuel tank has improper molding. Due to repeated expansion and contraction of the fuel tank, cracks may develop in the vent ring. Consequently, when fuel …
ローバー Land Rover Discovery V8i 1993–1998
ローバー Range Rover 1993–1998
ローバー Range Rover Vanden Plas 1993–1998
Improper welding at the lower mounting point of the rear suspension shock absorber may cause the affected area to fracture due to vibration during operation, potentially resulting in loss of vehicle functionality.
Triumph T100 2003–2004
Triumph Thruxton 2003–2004
Triumph Bonneville Black Edition 2003–2004
Improper machining of the right-side rod in the power steering cylinder results in insufficient rod strength. Repeated steering operations may cause cracks to develop at the pin hole section of the rod. …
小松 - 2002–2004