Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
5188 matching recalls · page 146 of 173
Front hub strength is insufficient. Repeated high-frequency cornering may cause cracks to develop near the base of the hub flange. Additional factors such as maintenance condition and load conditions may accelerate crack …
In vehicles modified from two-wheel drive to four-wheel drive, the rivets securing the steering gear bracket to the vehicle body have insufficient strength. Repeated maximum steering angle turns can cause these rivets …
The strut plate that retains the front wheel coil spring has insufficient strength. Repeated stop-and-go driving in high-temperature, high-humidity environments can cause cracks to develop in the plate, resulting in abnormal noise. …
The headlight leveling system contains an angle sensor linkage bracket mounted on the left rear trailing arm with improper installation methods. When the vehicle is lifted and the rear suspension is fully …
The fuel pump flange ring nut is insufficiently torqued, causing elevated fuel tank internal pressure to force fuel to leak from the gasket between the ring nut and fuel tank. In the …
④The fuel level sensor mount gasket has insufficient dimensions, which may cause fuel to leak from the mount due to engine vibrations, potentially resulting in fire.
③Insufficient fastening torque on the fuel pump flange causes fuel leakage from the flange due to increased internal pressure in the fuel tank, potentially resulting in fire.
Insufficient tightening of fuel hose clamps may allow fuel leakage at the clamp connection due to engine vibration and similar factors, potentially resulting in fire.
① Some fuel hose connectors have O-rings that can become misaligned during connection/disconnection. Repeated connection/disconnection cycles may damage the O-ring, causing fuel leakage, which in worst cases could lead to fire.
The bracket position of the frame fixing the steering gearbox is misaligned, causing positional deviation between the steering gearbox and intermediate gear coupling. If continued in this condition, the coupling fastener will …
Improper securing method of electrical wiring (signal and power supply) causes the wiring to interfere with the swivel stopper bracket and pipe clamps due to vibration during operation, resulting in wiring damage. …
Improper installation of brake system electrical wiring allows the wiring harness clamp to contact the brake pipe due to vibration during operation. Continued use may result in brake pipe damage, brake fluid …
The power steering hydraulic hose in the steering system has insufficient heat shielding. Repeated high-speed continuous driving and hill climbing in high-temperature conditions can cause the hose to degrade thermally due to …
The side-impact sensors in the airbag system have insufficient electromagnetic immunity. External electromagnetic interference may cause these sensors to transmit erroneous signals to the airbag control unit, potentially resulting in unintended deployment …
The interior finish of the passenger-side airbag door opening in the dashboard is inadequate, and burrs may form at the opening. If the passenger-side airbag deploys, the airbag may tear, reducing occupant …
In the rear axle power transmission system of four-wheel drive vehicles, some rear axle shafts have improper machining dimensions, and some have insufficient tightening of the lock nut that secures the rear …
Insufficient water protection on battery allows rainwater to contact the battery top surface. When the battery is replaced, depending on the filler cap design, rainwater may enter the battery interior, increasing electrolyte …
In the running gear, improper welding between the axle reinforcement plate and the air piping pad may cause cracks at the weld. If use continues in this condition, the axle may bend …
In the rear axle attachment section with a swinging mechanism, the mounting position of the swing stopper is inappropriate. Continued use on severely uneven road surfaces causes excessive load on the mounting …
In the rear axle attachment section with an oscillating mechanism, the oscillating stopper mounting position is inappropriate. Continued use on severely uneven road surfaces causes excessive load on the mounting plate that …
The high-pressure hydraulic hose for the power steering system is installed improperly, and may be damaged by engine vibration. This could result in power steering fluid leakage and increased steering effort.
The attachment bolts on the spool valve side of the steering rack are insufficiently tightened. Repeated steering operations and vibration during driving may cause these bolts to loosen. In the worst case, …
The rubber hose material of the fuel delivery hose is inadequate, which may cause fuel to leak from the joint between the rubber hose section and metal pipe section, potentially resulting in …
In right-hand drive vehicles, an incorrect component is installed in the brake pipe adapter connecting the brake master cylinder and brake pipe. Vibration during driving may cause the brake pipe and power …
Front hub strength is insufficient. Cracks may develop near the base of the hub flange when subjected to repeated high-frequency cornering. Additional factors such as maintenance condition and load capacity can accelerate …
In semi-trailers equipped with air suspension, the spring seat (a support base for springs mounted above the axle) has insufficient rigidity, causing excessive stress on portions of the axle and resulting in …
On electronically-controlled fuel injection-equipped vehicles, the adhesive bond between the fuel tank lower connector fitting and fuel hose is inadequate. Continued use may result in separation of the bonded joint, causing fuel …
Improper routing of the electrical wiring (main harness) causes interference with the return spring of the foot-operated parking brake pedal. Vibration during operation may damage the wiring, resulting in malfunctions of electrical …
The high-pressure relief valve installed on the travel pump of the hydrostatic transmission has inappropriate pressure settings and hydraulic release passage diameter. When performing sudden forward/reverse switching operations during travel, excessive pressure …
Some vehicles have drag links in the steering apparatus with mounting nuts lacking cotter pins. Repeated steering operations may cause these nuts to loosen. This creates play at the mounting point, and …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.