Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
5227 matching recalls · page 153 of 175
The intermediate arm shaft in the steering device linkage has inadequate strength, causing bending in some cases. Continued use in this condition may result in bearing damage and, in the worst case, …
In the braking system, the structure of the front-wheel brake hose and the positional relationship between the bracket securing the brake hose and the wheel cylinder are improper. When the brake hose …
The axle spindle in the running gear has insufficient strength. Continued use in this condition may cause cracks to develop in the spindle, and in the worst case, fracture and wheel detachment.
In hybrid system-equipped vehicles, charging control for the motor-drive battery is partially inadequate, which may cause temporary insufficiency of intake manifold vacuum acting on the vacuum-operated brake booster immediately after cold engine …
In the brake system, the gap between the brake pipe and leaf spring is improper, causing the brake pipe to contact the leaf spring and sustain surface damage. The surface plating peels …
In the front suspension system, some vehicles have insufficient bolt torque securing the strut to the knuckle. If operation continues in this condition, the strut may disengage from the knuckle when traversing …
The plastic nut securing the fuel pump unit to the fuel tank may be improperly tightened, with some units installed at an angle. If the vehicle continues to be used in this …
In the steering system, the steering arm mounting bolts and washers are made of inappropriate material. Repeated steering operations cause these bolts and washers to gradually deform, resulting in insufficient clamping force …
In the fuel system, certain fuel pumps have improper clearance between the internal rotating valve and the inner wall of the rotating valve chamber. Due to temperature fluctuations, the rotating valve and …
The auxiliary belt tensioner in the engine has improper tension settings, causing insufficient belt tension. The belt cannot follow engine speed changes and may slip off the pulley. This increases steering wheel …
In passenger-side airbags, some inflators have improperly installed check valve pins. During airbag deployment, the orifice for supplying inflation gas to the bag may not open correctly, preventing adequate airbag expansion and …
The combination switch for headlight and other controls, which is attached to the steering column cover, is inadequately secured. This can cause the cover to shift position. When the ignition key is …
In the starting system, due to inadequate dimensional accuracy of the ignition switch, the key cylinder interior does not rotate smoothly and may not fully return from the start position, causing the …
In passenger seat airbags, some units lack fastening bolts for the airbag unit mounting. During airbag deployment, this may cause abnormal deployment from the designed position, potentially causing severe injury to occupants.
In the power transmission system of four-wheel drive vehicles, the oil seal installation fixture for the rear differential is improper. During oil seal press-fitting by this fixture, the oil seal may be …
In the fuel system, the O-ring material at the connection of the fuel rail cross-over tube (pipe connecting left and right fuel rails) is inadequate. Prolonged engine heat causes this O-ring to …
In the electrical system, improper routing of electrical wiring may cause interference between the steering column and wiring when the steering wheel is turned. Continued use in this condition risks damage to …
In the braking system, the rear wheel brake pipe has an improper shape. During frequent acceleration and braking on snow-covered roads in severe cold conditions, large amounts of snow accumulated inside the …
The bracket (right side of two locations) that fixes the gearbox to the crossmember in the steering system has an improper shape. Frequent full lock steering operations can damage this bracket, resulting …
In welfare vehicles modified from standard vehicles with lowered rear floors for wheelchair accessibility, improper routing of the rear-wheel brake pipe in the braking system causes interference with the floor lift hydraulic …
In the engine starting device, high temperatures develop near the starter motor due to engine heat, and the fixed contacts of the starting electromagnetic switch have an inappropriate shape. Repeated starting operations …
In the braking and power transmission systems, vehicle body wiring routed improperly near brake pipes and clutch pipes may interfere with these pipes. Vibration during driving causes the brake and clutch pipes …
In the lighting system, oil used during press processing of the brake pedal bracket accumulated in recessed areas of the bracket. If used in this condition, the accumulated oil can penetrate the …
In right-hand drive vehicles, the side airbag control module circuit is improperly designed. During a collision, signals are not transmitted normally. When impact is received from the lateral direction under conditions for …
The ignition switch in the engine starting device has insufficient dust-sealing capability, allowing water and foreign matter to enter the interior. This can cause a short circuit between the battery supply circuit …
Due to improper design of the intake and exhaust manifolds in the engine, debris (such as leaves and grass) may accumulate on the manifold near the third cylinder. If vehicle operation continues …
In the engine, the mounting surface of the crankshaft timing belt guide plate has been machined improperly, resulting in insufficient mounting surface area in some units. Continued use in this condition may …
In the braking system, the shaft serving as the brake pedal pivot point and its lightweight alloy shaft holder have improper fitting. Repeated brake operation can cause the shaft to gradually slip …
In the braking system, the front wheel brake fluid supply pipe from the reservoir tank to the master cylinder has an improper shape. Minute air trapped in the master cylinder is not …
In the fuel system, some resin-made fuel pump mounting nuts on the upper portion of the fuel tank have improper heat treatment. Repeated temperature fluctuations may cause cracks in the nut, potentially …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.