Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
5227 matching recalls · page 62 of 175
1. In the power transmission device, the fastening method and torque specification for the belt-drive pulley fixing nut are inappropriate, resulting in inadequate clamping force in some units. Consequently, the nut may …
Improper routing design of the main wire harness can cause excessive tension on the hazard flasher wiring when the steering wheel is turned right, as the harness is pulled. Repeated steering operations …
In vehicles modified to dual-fuel (CNG/gasoline) specification, the CNG fuel control program is inappropriate. During idling while parked, if high electrical load is drawn (e.g., operating electric power steering with air conditioning …
In vehicles modified for dual natural gas/gasoline operation, the CNG filler neck mounting position and CNG fuel line routing are improperly designed, causing potential interference between the CNG fuel line and the …
In the braking system, the brake pipe routing between the master cylinder and ABS modulator valve is improper, causing the brake pipe to contact the exhaust manifold heat shield. Continued operation in …
Improper manufacturing of the control signal connector in the electric power steering system may allow moisture to enter the control unit. This can affect electrical signals, causing warning lights to illuminate and …
On van-bodied vehicles, improper instructions for chassis fastening positions during cargo body installation resulted in some units being fastened at positions differing from design intent. Continued operation causes excessive input from cargo …
Driver or passenger airbag units may have been equipped with non-conforming components due to improper manufacturing processes at the vehicle factory. This could result in failure to deploy properly when the airbag …
In the engine cooling system, some vehicles are equipped with defectively manufactured left-side engine oil cooler hoses (supply side) that have insufficient heat resistance. Due to thermal stress on the engine oil, …
Some steering gear boxes have insufficient strength due to improper manufacturing of the rack gear. During use, damage may occur, and in the worst case, steering control may become impossible.
The engine control module (ECM) of the wheel crane may emit an erroneous signal to the engine compression release brake actuation signal circuit, preventing the engine compression release brake from operating normally. …
In the wheel crane third and fourth axle steering mechanisms, improper adjustment of the steering stopper position causes the fourth axle to deflect under external tire forces during maximum steering and travel, …
Certain passenger-side airbag inflators have defective igniter composition due to inadequate manufacturing controls. The igniter charge does not meet design specifications. Consequently, the passenger-side airbag may not deploy during collision, risking serious …
On shovel loaders, the fastening instructions for the front axle and propulsion shaft joint fastening bolts are inadequate, resulting in insufficient clamping force in some units. Continued operation in this condition may …
In large dump trucks, the fuel tank mounting bracket at the rear of the vehicle was assembled in a state where it interferes with rivets on the side of the vehicle frame. …
During sunroof frame maintenance, improper assembly of the sunroof drainage outlet and drainage hose may prevent rainwater from being discharged through the hose. Rainwater that is not discharged externally may contact the …
①In large and medium-sized transit buses, the protective edge finish at the connection between the distribution box located below the driver's seat and the driver's side wall panel is inadequate, causing interference …
On large and medium-sized transit buses, the protective edge finish at the connection between the distribution box below the driver's seat and the driver's side wall panel is inadequate, causing the edge …
In the braking system, improper routing of the ABS front brake pipe may cause the pipe to contact and become damaged by the secondary air injection device due to engine vibration and …
The inflator (inflation device) for the passenger-side airbag may have inadequate moisture prevention of the gas generant. Under high-humidity environments with repeated temperature fluctuations, the gas generant may degrade. Consequently, the inflator …
In passenger-side airbag inflators, inadequate moisture protection of the gas generant can result in degradation when exposed to repeated temperature cycling in high-humidity environments. This may cause the inflator container to rupture …
In the Electronic Stability Program (ESP), due to an inappropriate control program, when the collision mitigation braking system or adaptive cruise control with distance control is deactivated due to road condition changes …
The steering coupling, which connects the steering shaft and steering gearbox, has insufficient fastening torque on its coupling nut. This causes wear of the coupling during full-lock turns or low-speed steering reversal. …
In the brake booster, due to improper material selection of the vacuum pipe connection and improper manufacturing of the vacuum pipe (including connection), the vacuum pipe connection may fracture under driving or …
In vehicles where the passenger seat airbag inflator has been replaced with a countermeasure unit, the airbag exhaust port is undersized. During airbag deployment, this can cause cracks in the airbag mounting …
The seal shape at the piston section of the brake master cylinder is inadequate, which may cause the seal to roll up when the brake pedal is depressed. This can result in …
In the electric parking brake system, some parking brake calipers have insufficient gear strength due to improper manufacturing. Motor actuation force may cause gear failure, potentially resulting in inability to release the …
Due to insufficient cooling during resin molding of the fuel tank, molding defects occurred at the fuel pump mounting screw boss, which may reduce seal performance with the fuel pump installed. As …
1. In the engine cooling system, improper coolant temperature control can cause the coolant temperature to rise rapidly when the engine is started under specific ambient temperatures and sudden acceleration occurs. This …
1. In the engine cooling system, improper coolant temperature control may cause coolant temperature to rise rapidly after engine start-up followed by hard acceleration under specific ambient temperatures. The resulting thermal stress …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.