Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
5188 matching recalls · page 116 of 173
The engine coolant temperature sensor harness is improperly secured. Engine vibration and similar forces can cause the conductor to break internally within the insulation. Continued operation in this condition causes the air …
The left-side knuckle arm in the steering device has insufficient strength. During turning, tire reaction force and power steering thrust may cause the knuckle arm to fracture, resulting in loss of steering …
The left-side gear case of the front axle has insufficient support strength. Under cornering loads from tire reaction forces and power steering thrust, internal bearings may fracture. This can cause wheel lock …
The program calculating particulate matter accumulation within the DPF (Diesel Particulate Filter) is deficient. Continued operation under high load with low engine RPM may prevent proper DPF active regeneration (combustion removal of …
The knuckle spindle on the rear axle has insufficient strength, and cracks may develop in this component. If the vehicle continues to be used in this condition, the knuckle spindle may fracture …
In the combination switch harness, improper routing of the wiring can cause the harness to become pinched between the combination switch mounting bracket and the steering column bracket when the steering wheel …
Internal insulation defects or poor contact pressure in the ignition coil may result in insufficient ignition, causing difficulty in engine starting and unstable engine operation. In the worst case, the engine may …
In the fuel injection system, improper machining of the fuel supply pump during manufacturing causes internal cracks in the pump, leading to fuel leakage that mixes with engine oil. Continued operation in …
At the rear suspension attachment point, the mounting bolt has inadequate strength due to improper heat treatment processing. Impact from road surfaces may cause bolt fracture, resulting in unstable vehicle attitude and …
During assembly of the brake light switch, insulating lubricating oil adhering to work gloves caused trace amounts of lubricant to enter the switch contact points, potentially generating insulating deposits on the contacts. …
Contact pressure management during manufacturing of the brake start relay and side stand relay is inadequate, resulting in some units with low contact pressure. Consequently, vibration during driving may cause contact failure, …
In the braking system of powder/granule transport semi-trailers, the adapter connecting the ABS modulator to the air chamber may be installed in reverse orientation. As a result, the adapter may loosen due …
In the brake hydraulic circuit of the power transmission device, due to machining defects in the inner sleeve mounting section (transfer cover) that forms the circuit, some units have the inner sleeve …
Improper lubricant used during brake light bulb socket manufacturing generates insulation on the bulb contact points, causing heat generation and resin deformation that may result in the brake light failing to illuminate.
Certain electrical wiring harnesses have inappropriately sized main and sub earth lines. Engine vibration may cause both earth lines to fracture, resulting in engine stall and inability to restart.
Due to improper airbag ECU programming, the front seat airbags may deploy inadvertently when the parking brake is engaged.
The front-wheel brake line geometry is inadequate, potentially causing stress at both ends of the line due to vibration during operation. This may result in crack formation at the affected area due …
In the brake booster of rail-road dual-use vehicles, defective welding of vacuum piping and incorrect vacuum hoses have been installed. As a result, insufficient negative pressure supply may occur, and in the …
Fire trucks equipped with engine block heaters (cold-start performance enhancement devices) have insulation caps on the terminals with insufficient heat resistance. Repeated prolonged energization over extended periods causes the cap to degrade, …
On vehicles equipped with electronic control suspension, the coil spring for the front wheel has an improper shape, causing the coating to peel and corrode at points where the spring rubs against …
The pinch prevention control of the rear left power sliding door is inappropriate. If the door lock position detection switch fails, the power door closing may incorrectly detect a foreign object in …
The front axle of large non-step buses has insufficient strength. Repeated rolling and lock-to-lock steering operations over extended periods can cause cracks to develop in the axle. Continued use in this condition …
Due to improper programming in the Engine Control Unit (PCM), engine idle speed may drop during steering operations and other maneuvers, with the potential risk of engine stall while driving.
Improper routing of the main harness may cause it to contact the bolt tip of the hydraulic rear suspension adjustment device or burrs on the frame weld. Continued use in this condition …
The front wheel brake line fastening method is inadequate, which may cause stress at both ends of the brake line due to vibration during operation. This may result in cracks forming in …
The electrical wiring connector inside the instrument panel is mounted in an improper position, allowing condensation from the air conditioning duct to enter the connector interior. Continued use in this condition may …
The acceleration sensor that detects the operation of the hydraulic-controlled front suspension may have improper solder processing on the circuit board, potentially preventing accurate measurement of vehicle height changes. This can cause …
The combination of motor brush material and steering gear ratio in the electric power steering (EPS) system is inappropriate. Repeated full lock steering operations cause excessive current to flow through the internal …
In the brake booster of dual-mode rail/road vehicles, defective welds in vacuum piping and incorrect vacuum hose assembly have been identified. Insufficient vacuum supply may result, potentially causing extended braking distance in …
The pivot pin for the secondary-axis steering lever in the steering device has improper machining at the corners, resulting in rough surfaces on some units. This may reduce the strength of the …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.