Front-wheel drive shafts may contain excessive moisture in the lubricating grease used in the wheel-side joint. This can cause temporary loss of the lubricant film when the steering is fully turned during …
Toyota bB 2002–2003
Toyota Will Cypher 2002–2003
Toyota ist 2002–2003
Toyota Vitz 2002–2003
Toyota Funcargo 2002–2003
+1 more
Due to improper mounting structure of the front impact sensor that detects collision impact early during offset collisions, the mounting bolts may loosen. Consequently, the sensor may fail to detect impact during …
Mitsubishi Outlander 2005–2006
The parking mechanism actuator lever of the automatic transmission (mechanism that mechanically locks the transmission output shaft) has improper machining. When shifted to park position, the lever interferes with the valve body, …
Mitsubishi i 2006
The passenger seat airbag folding method is improper, which may prevent full deployment during initial actuation due to contact resistance with the case sidewall. As a result, internal pressure within the airbag …
Mitsubishi i 2005–2006
The relay, fuse, and electrical wiring for the heated windshield on snow removal vehicles have insufficient capacity. When used continuously for extended periods, the wiring may overheat. Continued use can result in …
Mitsubishi Fuso 1996–2005
Insufficient clearance between tire/wheel sidewall and rear axle. When steering is operated to maximum lock angle, tire/wheel sidewall may interfere with the rear axle. Continued use could damage the tire and, in …
S N FD30PX 2006
S N FT30PX 2006
On flip-up seats located adjacent to emergency exits in buses, some units have weak pin retention force securing the seat, some have insufficient overlap in anti-tip brackets due to installation variance, and …
Mitsubishi Fuso 1988–2002
Mitsubishi Fuso Aero Queen 1988–2002
Mitsubishi Fuso Aero Star 1988–2002
Mitsubishi Fuso Aero Bus 1988–2002
Mitsubishi Fuso Aero Midi 1988–2002
①The electrical wiring for the fuel pump is routed improperly in some cases, causing contact with the exhaust pipe. Continued operation in this condition may result in insulation melting and short-circuiting, potentially …
ドカテイ ST3 2005–2006
Injuries — Risk of handbrake cable coming loose. Possible opening of handbrake lever on rear brake caliper.
In the steering gear of the steering apparatus, the pinion shaft bearing may not be assembled during the manufacturing process. As a result, the pinion shaft may not be securely retained, and …
Nissan March 2002
Due to inadequate material specifications for the O-ring and improper tolerance control during manufacturing of the spacer in the vehicle speed sensor mounted on the final drive, the airtightness of the sensor …
BMW HP2 2005–2006
BMW R1200S 2005–2006
In spring-applied parking brake actuators, improper installation of the screw securing the water ingress prevention cap allows water to enter the spring chamber, causing spring corrosion. Spring fracture may occur, damaging the …
Mitsubishi Fuso 1996–2005
In spring-applied parking brake actuators, the screw retaining the water ingress prevention cap has an improper shape, allowing water to enter the spring chamber and cause spring corrosion. This can result in …
Mitsubishi Fuso 1996–2005
In spring-applied parking brake actuators, improper installation of the water ingress prevention cap allows water to enter the spring chamber, causing spring corrosion. This can lead to spring fracture and diaphragm damage, …
Mitsubishi Fuso 1996–2005
In vacuum-assisted brake boosters, the vacuum hose material is inadequate, and ozone degradation can cause early cracking. Continued use in this condition allows the crack to propagate, and in the worst case, …
オペル Speedster 2002–2003
In the braking system, an incorrect front brake hose was installed, resulting in some units where the ferrule shape that secures the hose to the brake caliper is inappropriate, causing the brake …
Daihatsu Hijet 2006
The bushing dimensions in the link mechanism that secures the stabilizer to the chassis are improper, resulting in poor sliding friction of the bushing during front suspension vertical movement in some units. …
Hino Hino Dutro 2003–2006
Toyota Toyota Dyna 200 2003–2006
Toyota Toyota Dyna 300 2003–2006
Toyota Toyota Toyoace G25 2003–2006
Toyota Toyota Toyoace G35 2003–2006
The ABS warning lamp (integrated with ABS cancel switch), which illuminates when ABS is disengaged or malfunctions, has inadequate water-resistant design. Water intrusion causes internal corrosion, potentially preventing the warning lamp from …
KTM 990 ADVENTURE 2005–2006
The fuel hose material for the generator is inappropriate, causing premature deterioration in some units. Continued use may result in cracks in the fuel hose leading to fuel leakage, which in the …
Fiat Barstner 2001–2006
The air charge pipe routing is improper, causing interference between the pipe and the underfloor support member (sill) in some vehicles. Continued use in this condition may result in pipe damage due …
Mitsubishi Fuso Aero Star 1997–2000
In vehicles equipped with Hill Start Aid (HSA), the control solenoid valve has inadequate waterproofing, allowing water containing de-icing agent to enter internally. This causes internal corrosion, resulting in the hydraulic circuit …
Isuzu Elf 1994–2000
In spring-applied parking brake systems, the material of a portion (elbow fitting) of the piping connecting the spring chamber and service brake chamber is inappropriate. Deterioration over time causes cracks to develop, …
Isuzu GIGA 2001–2003
In spring-applied parking brake actuators, improper installation of the screw that secures the water ingress prevention cap allows water to enter the spring chamber, causing spring corrosion. This can lead to spring …
Isuzu GIGA 2001–2003
In spring-applied parking brake systems, the elbow section of tubing connecting the spring chamber to the service brake chamber is made of inappropriate material. Time-dependent deterioration causes cracking, allowing water to enter …
Hino Hino Profia 2003–2005
In spring-applied parking brake actuators, improper installation of the fastener securing the water ingress prevention cap allows water to enter the spring chamber, causing spring corrosion. This can lead to spring fracture …
Hino Hino Profia 2003–2005
The ignition coil manufacturing process for the engine is improper, resulting in damage to the igniter built into some ignition coils. Continued use in this condition may cause the coil and igniter …
Mazda Demio 2005
Mazda Verisa 2005
The brake pad material of the primary braking system is inappropriate, causing pads to reach high temperatures and expand due to friction heat during braking. Continued use in this condition may cause …
Volvo FH FM 2006
Some vehicles lack a lock plate on the brake pedal's fold-down mechanism, which is designed to provide clearance between the brake pedal and lower limbs during severe impacts such as collisions. As …
Renault Mégane 2003–2004
During vehicle manufacturing, improper lubricant was applied to the contact points of the brake light switch. Heat generated during contact engagement/disengagement oxidizes the lubricant components, increasing contact resistance at the switch contact …
Honda Fit 2005
Injuries — The product poses a risk of injury caused by vehicle impact because testing revealed that parking brake may not engage or fails to hold the vehicle.