Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
5227 matching recalls · page 137 of 175
The tie-rod spring, which prevents detachment of the tie-rod that controls fuel injection volume in the engine, has insufficient strength. Repeated engine shutdowns can cause the spring to fracture. If the vehicle …
The fuel injector control rod incorporates a retaining spring that lacks sufficient strength to prevent detachment. Repeated engine shutdowns can cause this spring to fracture. If operation continues in this condition, the …
The steering gearbox mounting bracket attached to the front subframe has insufficient strength. Repeated steering maneuvers such as lock-to-lock turning may cause cracks to develop in the bracket. Continued use could result …
Improper exhaust pipe mounting can cause cracking due to engine vibration. Continued use may result in noise exceeding regulatory limits, or exhaust heat may melt electrical wiring insulation, causing short circuits that …
In the power transmission device, the power supply coil mounting terminal (lead) attached to the control board within the multi-transmission power unit that controls the power system of the chassis has insufficient …
②The adjuster lever mounting structure on the rear drum brake of the brake system is inadequate for automatically adjusting clearance between drum and shoe according to lining wear. Repeated use of parking …
①The link plate that retracts the brake shoe to its original position when releasing the rear wheel drum brake lacks sufficient strength. Repeated use of the parking brake alone to stop the …
Some brake pipes are not properly secured, and may contact and wear against the exhaust pipe due to vibration during operation. Continued use may result in brake pipe perforation, brake fluid leakage, …
Due to improper engine control unit programming, warning lights may illuminate suddenly during operation. Engine speed control becomes impossible, with throttle inputs failing to increase engine speed or engine speed increasing uncontrollably, …
Hub nut fastening torque management on front and rear wheels is improper, which may cause hub nuts to loosen during operation. Continued driving in this condition may result in hub nut detachment …
In the braking system of four-wheel-drive vehicles, the capacitor, a component of the deceleration sensor (G-sensor) used for ABS control, may leak electrolyte after prolonged use. If use continues in this condition, …
The mounting bracket that supports the cooling water line for the fluid-type auxiliary brake device attached to the transmission has insufficient strength. Due to vibration during operation, the bracket may crack or …
The hydraulic control valve in the accumulator (a device that temporarily stores hydraulic pulsations to reduce fluctuations) incorporated in the brake booster (brake hydro-boost module) that reduces brake pedal effort has defective …
The electrical circuit of the auxiliary braking device (electromagnetic retarder) is improperly configured, causing the brake light to not illuminate when the electromagnetic retarder is engaged.
Inadequate welding between the rear suspension coil spring seat (lower seat) and the rear axle beam causes the weld to separate under driving vibration, tilting the seat. This allows the brake pipe …
⑤ The attachment point of the steering lever pivot support lacks sufficient strength. If steering is operated in the workshop with only the slewing body of the crane attachment device mounted, cracks …
③The sealing ring material used in the pipe joint at the air compressor outlet is inappropriate, and the union nut may loosen due to engine vibration and other factors. As a result, …
②Insufficient clearance between the exhaust brake air hose and accelerator cable relative to the exhaust pipe may cause the protective covering of the hose or cable to melt due to exhaust pipe …
In slide-bed vehicle transport vehicles, the mounting plate that secures the loading ramp for loading vehicles has insufficient strength. Vibration during operation can cause cracks to develop at the welds of this …
The fuel injection system fuel pipe clamp on the installed Mitsubishi Fuso Truck and Bus engines has an improper structure. Engine vibration causes the clamp bolts to loosen and the clamp may …
In the Mitsubishi Fuso Truck and Bus engines installed in these vehicles, the clamp structure securing the high-pressure fuel pipe of the fuel injection system is inadequate. Engine vibration causes the clamp …
The clamp structure securing the high-pressure fuel pipe of the fuel injection system is inadequate. Engine vibration can cause the clamp bolts to loosen and the clamp to detach. Continued operation may …
Improper routing of electrical wiring within the meter cluster can cause the wiring to contact the tachograph mounting bracket when the steering wheel is slid to the fully forward position, resulting in …
On large trucks, the brake pipe on the flywheel housing side was installed with deformation, causing interference with the transmission shift rod located in close proximity. Continued use in this condition may …
The ferrule angle at the parking brake air hose switchover valve mounting is inappropriate, causing potential interference between the rear wheel brake air hose and parking brake air hose during vehicle body …
In police vehicles, the rubber diaphragm in the brake booster has insufficient heat resistance. Heat exposure in the engine compartment causes thermal degradation and cracking of the diaphragm. Continued use allows the …
Some fuel hoses and fuel pump assemblies are improperly fitted, causing stress at the fuel hose attachment point. Continued use in this condition may result in the attachment point fracturing due to …
In vehicles equipped with rear-axle 4-bag air spring dampers, incorrect parts were installed in the air springs, resulting in insufficient clearance between the air spring diaphragm and stabilizer bracket, causing interference in …
① The air brake hose routing of the spring-applied parking brake is improper, causing the hose to interfere with the air spring in some cases. Continued use in this state may result …
In vehicles equipped with 4-bag air spring suspension systems, the V-rod that secures the rear axle to the frame has insufficient fastening strength on the ball joint mounting nut connecting to the …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.