Before you buy, check it isn't under a dangerous recall.

Driver-side or passenger-side airbag inflators may have inadequate moisture protection of the gas generant. Repeated temperature fluctuations in high-humidity environments can degrade the gas generant, potentially causing inflator container rupture during airbag …

In small buses, the automatic transmission fail-safe control program is inappropriate. If the vehicle speed sensor malfunctions, fail-safe does not activate, and the transmission may unexpectedly downshift to a low gear during …

On large trucks, the stabilizer arm of the rear axle air suspension has insufficient strength. Repeated turning can cause cracks to develop in the arm. If operation continues in this condition, in …

In ladder fire trucks, the steering idler arm lacks sufficient strength. Repeated full-lock steering operations can cause cracks to develop in the arm. Continued use may result in arm fracture in the …

In combination tail light and brake light assemblies, improper socket manufacturing results in insufficient press-fitting of the bulb retaining clip. Consequently, the clip may disengage due to vibration during operation, and if …

Due to inappropriate control programming in the auxiliary power module, during the transition from idle-stop deceleration to re-acceleration, the module may incorrectly judge the high current flowing through the starter-generator as excessive …

The capless fuel inlet cap seal material is inadequate, causing loss of sealing integrity when exposed to moisture from detergents and other sources. This allows rainwater and other contaminants to enter the …

In the fuel system, improper manufacturing of the high-pressure fuel pump can cause wear to the piston that pressurizes fuel in the pump. This results in reduced fuel supply, and continued operation …

Voltage fluctuations supplied from the battery and manufacturing variations in the fuel pump may cause premature wear of internal components. Continued use in this condition can lead to progressive wear, resulting in …

In the engine cooling system, due to inappropriate programming of the engine control unit, when foreign matter or debris obstructs operation of the auxiliary coolant pump, the motor within the pump may …

In the fuel system, improper installation position of the fuel pump filter flange can cause premature deterioration of the flange due to water exposure from rain and other sources. This reduces flange …

In heavy-duty tractor brake relay valves, improper manufacturing of the pressure sensor that measures brake pressure can cause the sensor's IC chip to detach from the sensor substrate. Continued use in this …

In the brake system, the rear brake hose assembly instruction is inappropriate, causing the hose to contact the muffler in some cases. The muffler heat melts the hose at the contact point, …

In the driver's seat, improper routing of wiring in the electric adjustment mechanism (electric power seat) can cause the wiring to contact the edge of the power seat motor when the seat …

The passenger seat airbag warning label displayed on the passenger sun visor and similar locations contains incorrect content, failing to comply with Safety Standard Article 18.

In the power transmission system, the joint disc connecting the propeller shaft to the transmission has been manufactured improperly in some cases, resulting in insufficient strength. Consequently, the disc may fracture under …

Due to improper dashboard manufacturing, the passenger-side airbag opening is not correctly machined on some units. As a result, the airbag may not deploy normally during a collision, potentially causing excessive injury …

The joint disk connecting the propeller shaft and transmission in the power transmission system may have insufficient strength due to improper manufacturing. Consequently, the disk may fracture under driving torque. If vehicle …

During maintenance operations on the sun visor, improper instructions in the service manual may cause the vanity mirror lamp wiring to contact and damage body panels. This can result in short circuit …

The ABS module contains improper vehicle speed detection programming, preventing vehicle stop information from being transmitted to the steering lock control module (KVM). As a result, the steering lock unit receives no …

The brake caliper boot seal structure on the rear wheels is inadequate, allowing water ingress into the caliper interior. This causes corrosion and rust on the shaft. Continued use may deteriorate shaft …

In the fuel system, the fuel pump filter flange mounting position is improper, causing the flange to degrade prematurely due to water exposure from rain and similar sources. As flange strength diminishes, …

Certain brake device brake pistons have an incorrect oil seal installed in the piston section, resulting in insufficient sealing. This may cause brake fluid leakage. Continued operation in this condition will result …

In trailers compliant with mid-period brake regulations equipped with single or lift axle configurations, air leaks may occur due to related components such as air control valves being used beyond their replacement …

The meter panel display may show nothing upon engine start due to an inappropriate display program. Additionally, the display program may reset while driving, causing the speedometer, odometer, fuel gauge, and other …

In the electric power steering system, improper manufacturing control of the electric motor has resulted in some units without terminal welding. Continued use in this condition may cause terminal connections to disconnect, …

The airbag inflator units have improper manufacturing controls, resulting in igniter charges that are not formulated to design specifications. Consequently, airbags may fail to deploy upon collision, risking severe occupant injury.

On trailer axles, the wire attachment position of the catch strap device—which limits the extension height of the air suspension—is improperly positioned, resulting in interference between the wire and axle in some …

The airbag control unit program for the passenger seat airbag is defective, causing the airbag deployment signal to not be transmitted to the airbag inflator in some vehicles. As a result, the …

In articulated bus engines, the retaining force of spacers designed to prevent fuel hoses from contacting each other is insufficient. Engine vibration can cause these spacers to loosen or detach. Continued operation …