Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
5227 matching recalls · page 101 of 175
In braking systems equipped with a dual combined brake system that allows front and rear wheel brakes to operate in coordination, the structure of the secondary master cylinder that transmits braking force …
The gas generant in the driver-side SRS airbag inflator contains defective material. If the airbag deploys, abnormal pressure rise within the inflator may rupture the container, scattering component fragments and potentially injuring …
The driver-side SRS airbag inflator contains defective gas propellant. Upon airbag deployment, abnormal pressure rise within the inflator may cause the container to rupture and scatter component fragments, potentially injuring occupants.
The design evaluation of the operating circuit for the electric auxiliary coolant pump that cools the turbocharger was insufficient. Continued use in this condition may cause metallic substances to be generated on …
Insufficient design evaluation of the operating circuit for the electric auxiliary coolant pump that cools the turbocharger. Continued use in this state may cause metallic substances to form on the circuit board, …
The design evaluation of the operating circuit for the electric auxiliary coolant pump that cools the turbocharger was insufficient. Continued use in this condition may cause metallic substances to form on the …
The pipe section of the power steering high-pressure hose may have an inadequately thin coating due to improper management of the plating process duration. Continued use in this condition can result in …
The attachment nut of the ball joint stud bolt connecting the front lower arm and knuckle arm of the suspension may loosen during use. Continued operation in this condition can result in …
The left and right rear brake hoses have been installed with improper pipe routing angles, causing some hoses to be positioned too close to the adjacent rear suspension springs. Continued use in …
Manufacturing tolerances in the electric parking brake equalizer (device that distributes parking brake operating force equally to both wheels) may result in defects. Continued use in this condition could cause vibration to …
Injuries — null The belt for the power steering pump may become detached from the pulley which could result in a sudden increase in steering effort and lead to a road accident.
Improper welding between the side frame and front lower cross member results in insufficient weld strength in some vehicles. Continued operation may cause weld separation due to driving vibration, resulting in misalignment …
In vehicles equipped with manual transmission assist (Honda Techamatic), the bearing section of the brake linkage mechanism has an improper structure, which may cause excessive stress on the bearing section. Continued use …
The electric power steering control unit has improper machining of the control board mounting holes, causing control board deformation in some units. Continued use may result in solder separation on the control …
Assembly variation in fuel piping and related components of the fuel tank fuel pump unit may result in insufficient strength at the fuel supply piping assembly joint. Continued operation may cause cracks …
(1) In the combination lamp (tail light, brake light, and turn signal) bulb holder, the terminals of the electrical wiring connector may be deformed. As a result, insulating material may form on …
The rear stop lamp switch has insufficient heat resistance to exhaust manifold temperatures, causing the resin component to deform from thermal exposure. This results in brake fluid leakage, reduced rear brake braking …
In vehicles equipped with integrated front and rear seat headrest airbag systems, improper wiring assembly of the rear side impact sensor may cause delayed airbag deployment in situations where the airbag should …
The electrical wiring connected to the Electric Power Steering Control Unit (EPS-ECU) is improperly secured. Due to running vibration and similar factors, micro-sliding occurs between the EPS-ECU connector terminals and the electrical …
On the engine crankshaft pulley, some units have insufficient adhesive application between the outer ring and vibration damper rubber. This can cause the adhesive bond to separate, resulting in the outer ring …
On forklifts, insufficient clearance exists between the steering wheel rear tire and rim side surface and the rear axle. When the steering is operated to maximum turning angle, the rear tire and …
In light-duty trucks, improper machining of the knuckle fitting hole in the knuckle adapter may result in insufficient bolt tension on the adapter mounting bolts. Continued use in this condition may cause …
In the braking system, inadequate startup management of the equipment that applies grease to the pivot portion of the front-wheel brake lever results in insufficient grease application to the pivot portion. The …
During engine side mount installation work, the insulation of electrical wiring (engine room wire harness) may be damaged by tightening bolts. As a result, vibration during driving may cause the wire insulation …
Primary brake system brake pads have insufficient adhesion between friction material and backplate. Depending on usage environment, water can infiltrate the adhesion interface, causing corrosion. In worst case, friction material may separate, …
The air intake duct structure is inadequate, which can cause the metal connector portion of the duct to contact the fuel pipe. This may cause the fuel pipe to wear, and in …
The waterproofing structure around the throttle cable in the acceleration system is inadequate. Water may enter inside the cable during rainy conditions and other wet-weather operation. In sub-freezing ambient temperatures, water trapped …
The brake lamp switch has insufficient durability internally, causing wear and thermal deformation due to temperature rise during use, which may result in electrical contact failure. Continued use may cause the switch …
The rear wheel braking system has inadequate waterproofing around the brake cable. Water may enter the cable interior during rain or wet conditions. In sub-freezing environments, this trapped water can freeze, potentially …
The front brake cable assembly has inadequate water-sealing around the cable. Water may enter inside the cable during wet weather operation. In sub-freezing ambient temperatures, water trapped in the dust boot at …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.