Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
5227 matching recalls · page 141 of 175
The feed hose length of the hydraulic power steering system is inappropriate. When the steering wheel is quickly returned from full lock, hydraulic pressure fluctuates sharply at the valve that switches oil …
Improper assembly of the fuel line quick connector fitting has resulted in insufficient engagement of some quick connectors. Continued use may cause the quick connector to shift under fuel pressure, compromising the …
The bearings of the brake hydraulic pump drive gear mounted inside the engine have improper machining, which may cause the bearings to wear rapidly. If operation continues in this condition, the brake …
In the brake hydraulic pump, the fixing method for the pressure adjustment screw of the control valve is inadequate, which may cause the nut securing the screw to loosen. Continued operation in …
The castle nut fastening torque for the ball joint connection of the tie rod linking the rear axle center arm and knuckle is insufficient. Repeated steering inputs can cause the castle nut …
Certain check valve caps between the brake booster and intake manifold have improper welding, which may cause the check valve cap to detach due to engine vibration and similar conditions. This results …
The vent ring welded to the plastic fuel tank has improper molding. Due to repeated expansion and contraction of the fuel tank, cracks may develop in the vent ring. Consequently, when fuel …
Improper welding at the lower mounting point of the rear suspension shock absorber may cause the affected area to fracture due to vibration during operation, potentially resulting in loss of vehicle functionality.
Improper machining of the right-side rod in the power steering cylinder results in insufficient rod strength. Repeated steering operations may cause cracks to develop at the pin hole section of the rod. …
The rear combination lamp's red lens, which serves as both a tail light and brake light, has insufficient weather resistance. Prolonged exposure to strong sunlight causes the red color to gradually fade, …
The rear combination lamp's tail light and brake light dual-purpose red lens has insufficient weather resistance. Prolonged exposure to strong sunlight causes the lens red color to gradually fade, risking non-compliance with …
The wedge structure of the expander that extends the brake shoes in the primary braking system is defective. When brake linings wear beyond the service limit or shoe gap becomes excessive, the …
Due to inappropriate engine control unit programming, the throttle valve exhibits excessive amplitude in its closed position, which may cause the electronic throttle motor stopper to fracture. Consequently, engine control may enter …
The air piping (nylon tubing) for the parking brake (wheel parking brake) is routed improperly, causing the nylon tubing to soften due to engine heat in some cases. As a result, the …
The float stopper structure in the brake fluid reservoir's brake fluid leak warning system is inadequate. During manufacturing, when brake fluid was pressurized and injected on the production line, the float became …
In independent suspension systems, the front suspension arm and rear suspension arm (on dual rear-axle vehicles) have insufficient rigidity. Road surface inputs during driving and braking inputs may cause cracking in the …
In the rear axle tube of low-floor, dual rear-axle heavy-duty trucks, improper die management during forging resulted in some vehicles being assembled with damaged tube components. Consequently, repeated input loads from road …
① In the ball joints of upper and lower arms on independent front suspension systems of small trucks, improper dust boot seal design allows mud and water ingress, causing wear of plastic …
The relay rod of the steering apparatus has insufficient strength. Prolonged frequent use involving high steering forces, such as lock-to-lock steering operations, may cause cracks to develop. Continued use allows cracks to …
The bracket (right side of two locations) that secures the steering gearbox to the cross member has insufficient plate thickness in some units. Frequent full-lock steering operations can damage this bracket, resulting …
On vehicles equipped with power steering, the knuckle arm has insufficient strength. Repeated full-lock steering and high-frequency steering operation can cause cracks to develop in the arm. If use continues in this …
In vehicles equipped with electronic stability control, the surface treatment of the rubber damper inside the acceleration sensor that detects skidding is inadequate. Continued use may cause the rubber damper surface to …
On aerial work platforms, improper installation of the exhaust pipe has resulted in gaps forming at the clamp tabs in some units. Continued operation may cause the clamp bolt to fracture, causing …
The bracket securing the suspension lock cylinder, which locks the buffer device during operation, has insufficient strength. As a result, cracks may develop in the vehicle frame at the bracket mounting points …
The electronic control unit (ECU) governing the mechanical automatic transmission has an improper control program. When the vehicle is stopped in Drive range without depressing the clutch pedal, the clutch remains in …
The material of the rear axle shaft in large trucks with rear-axle drive is inappropriate, resulting in insufficient strength near the flange root against excessive input during start-up. Therefore, the shaft may …
The oil seal and O-ring of the chain-drive power transmission device (transfer case) have insufficient heat resistance. During continuous high-speed driving, if transfer oil temperature rises, the oil seal or O-ring may …
In turbocharged manual transmission vehicles, the fastening bolt of the Oil Control Valve (OCV) cover—which hydraulically controls engine intake valve timing—has insufficient bolt preload. Under sustained high-load, high-RPM operation, internal engine vacuum …
The gap between the snap pin (which prevents the connecting pin from coming out between the right brake pedal and brake link) and the brake pedal support is improper. During brake operation, …
The heat protector mounting bracket attached to the vehicle frame has an inadequate design, resulting in insufficient strength. Vibration during driving may cause the bracket to fracture, allowing the heat protector to …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.