Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
5227 matching recalls · page 154 of 175
In the braking system, some units have improper brake shoe adjustment methods, causing the brake mounting plate to vibrate and generate abnormal noise during braking. If operation continues in this condition, the …
In the parking brake system, improper lubricant was used during installation of the rubber boots for waterproofing and dust protection on the wheel cylinders of the air-operated parking brake. This caused the …
The welded joint shape of the high-pressure pipe bracket mounted on the rear end of the fuel injection pump is improper. Due to vibration during operation, the bolt fastening this bracket may …
Due to inadequate manufacturing process control of the crankshaft, residue may adhere to the pulley bolt threads. This results in insufficient clamping force on the pulley mounting bolt. Continued use in this …
In welfare vehicles modified from standard vehicles with lowered rear floors for wheelchair accessibility, the rear wheel brake pipe routing in the braking system is improper. When the rear floor is lowered …
In the passenger seat airbag, some inflators lack an installed check valve pin. When the airbag deploys, the orifice for supplying inflation gas to the bag cannot open properly, preventing adequate airbag …
The auxiliary hydraulic system sub-return hose equipped in the steering and braking systems may be installed in a twisted condition. During cab tilt operation, the hose can catch on the heater hose …
The sub-return hose of the hydraulic system for power assistance equipped in the steering and braking systems may be installed in a twisted condition. During cab tilt operation, the hose can catch …
In the fuel system, the fuel return pipe attached to the fuel pump has an inadequate length, resulting in insufficient clearance with the pump case. When the engine is stopped with low …
The passenger-side airbag inflator contains a welded joint between the diffuser and gas generator body that may be improperly welded. Upon airbag deployment, this joint may separate, causing the diffuser to detach. …
Certain passenger-side air bags have improper welds at the joint between the diffuser and gas generator body within the inflator. When the air bag deploys, the joint may separate, causing the diffuser …
In the air-operated parking brake system, the air exhaust mechanism of the air chamber is inadequate, allowing mud and water to enter the chamber. When the ventilation hole becomes blocked and the …
Certain vehicles have insufficient clamping force on the rear wheel lock screws (screws that prevent wheel bearing nut loosening) in the running gear. Due to vibration during operation, the lock screws may …
Improper battery mounting position allows rainwater to enter the battery through the filler cap vent hole, increasing internal fluid level and causing overflow. Spilled battery fluid contacts the left front wheel brake …
Certain passenger-side airbag inflators have improper welds at the joint between the diffuser and gas generator body. When the airbag deploys, the weld may separate, causing the diffuser to detach. This prevents …
In the fuel system, the threaded portion of the fuel pump unit fastening nut in the fuel tank was manufactured improperly, resulting in some fuel pump units not being sufficiently tightened during …
In the acceleration system, the throttle holder mounting position on the right side of the handlebar is improper, which may cause interference between the throttle grip and the handlebar end counterweight. This …
In the electrical system, improper routing of the positive battery cable may cause it to contact vehicle body parts due to vibration during acceleration and deceleration of the automatic transmission. This can …
In the fuel system, certain fuel filter-to-fuel pipe connection retainers have improper geometry. Vibration during driving may cause the connection to separate, resulting in fuel leakage. In worst-case scenarios, this could lead …
In the fuel system, the seal at the fuel pump and gauge unit mounting location on the fuel tank has an inadequate gasket design, resulting in insufficient sealing. Fuel may leak from …
In the fuel system, when installing the fuel pipe connected to the check valve (one-way valve) of the fuel pump attached to the engine, excessive friction resistance at the delivery pipe side …
In the power transmission device, some auxiliary transmission clutch housings have dimensional defects due to manufacturing variation. This can cause interference with the outer circumference of the clutch piston, which in worst …
In the power transmission system, the travel controller program that controls the travel motor is inappropriate. When low-speed sharp turning and braking operations are performed simultaneously, excessive tension develops in the drive …
During manufacturing of the alternator, distortion occurred inside the diodes of the rectifier circuit in some units. This accelerated thermal degradation and damage to the diodes, causing excessive current to flow through …
In the braking system, some vehicles are equipped with front brake hoses and front brake hose No. 2 that are longer than the original specification. During steering operation, the front brake hose …
At the vehicle body mounting location of the steering system gearbox, improper welding of the reinforcement plate can lead to cracking when the steering shaft experiences repeated excessive loads during maneuvers such …
In the braking system, defective welds exist on the rear suspension arm support bracket welded to the rear axle housing. The bracket may separate at the weld joint. The brake tube fixed …
In the lighting system, the brake light unit structure is inappropriate, allowing condensation water inside the unit to accumulate in the bulb socket without being drained, which can corrode the contacts, causing …
In the steering system, improper routing of the power steering hydraulic hose results in insufficient clearance between the hose and exhaust pipe in some vehicles. Heat from the exhaust pipe causes the …
The driver-side airbag inflator (gas generator) ignition device manufacturing process is improper, causing the ignition material inside the ignition device to separate in some units. The airbag may fail to deploy during …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.