Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
5188 matching recalls · page 158 of 173
Certain vehicles lack hydraulic damping mechanisms within the hydraulic piping of the engine compartment's anti-roll system (anti-sway mechanism). Continued operation in this condition can cause vibration-induced damage at the connection between the …
In the fuel system, the electrical wiring of the fuel pump routed on the upper surface of the fuel tank has insufficient clearance from the reinforcement plate of the rear seat belt …
The brake booster cylinder in the control unit contains manufacturing defects that may prevent the piston from fully retracting even after the primary brake is released. Continued operation in this condition causes …
The rubber breather hose that vents air from the fuel tank during refueling contains material of inappropriate specification. Continued use in this condition may cause cracks to develop in the hose, resulting …
In the steering system, the clevis head attached to the tip of the power steering hydraulic cylinder and the center bell crank link component that distributes steering force to the front and …
Improper clamp fastening position on the fuel supply rubber hose of the fuel pump unit mounted on the fuel tank. Continued use in this condition may cause the rubber hose to loosen, …
Improper clamp fastening positions are present on the fuel supply rubber hose of the fuel pump unit attached to the fuel tank. Continued use in this condition may cause the rubber hose …
In the braking system, the left rear wheel brake pedal has insufficient weld strength. Continued use in this condition may cause the pedal plate to detach, and in the worst case, could …
In the braking system of motorized bicycles, the coupling structure between the equalizer-side connector of the right brake cable and the cable bracket in the linked brake mechanism (equalizer) for front and …
In the braking system, the air piping assembly at the relay valve section of the brake booster differs from the proper configuration. If any part of the brake piping becomes damaged, the …
The aluminum coupling connecting the steering gearbox and steering knuckle arm in the steering system has insufficient strength. Continued use in this condition may cause the coupling to separate, resulting in loss …
The aluminum coupling that connects the steering gearbox and steering knuckle arm in the steering system has insufficient strength in some vehicles. Continued use in this condition may result in separation of …
In vehicles with a roof (roof panel) modified to a flip-up type, the adhesive method for covers affixed to the entire roof is inappropriate. If use continues in this state, the cover …
In the engine starting device, improper assembly of the battery electrical terminal on the electromagnetic switch for the starter motor can cause the insulating resin bushing at the terminal to deteriorate and …
The accelerator cable is inadequately secured, causing it to drop from the top of the frame and contact the left front wheel brake pipe. Continued use in this condition allows engine vibration …
The clamp fastening position of the fuel supply rubber hose on the fuel pump unit attached to the fuel tank is inappropriate on some vehicles. Continued use in this condition may cause …
In the acceleration device (throttle grip) of two-wheeled motorcycles, the structure of the throttle grip's insertion into the handlebar pipe is inadequate, allowing water ingress into this area. This causes rust to …
The rear wheel braking system's swing arm brake caliper mounting point lacks sufficient strength. During rear braking, this mounting point may deform. If use continues in this condition, the brake caliper can …
In the brake system, some brake pipes between the brake master cylinder (hydraulic pressure source) and actuators (hydraulic control devices) are deformed during assembly. Continued use in this state may cause the …
Some front-wheel brake master cylinder rubber covers have defective sealing. If use continues in this condition, moisture can enter the cylinder, causing piston corrosion. In the worst case, the piston may seize …
Improper combination of the hydraulic control unit (HU) of the ABS (Anti-lock Braking System) brake control device and the rear wheel brake master cylinder. During braking with ABS activated, the piston stroke …
The crimping method at the metal fittings of rubber fuel hoses (supply and return sides) in the engine compartment is improper. Continued use in this condition may cause fuel leakage at the …
In vehicles equipped with automatic transmissions, the clearance between the power steering hydraulic piping of the steering force amplification device and the driveshaft dust boot clamp is inappropriate. Engine vibration may cause …
Certain side airbag devices in the driver and passenger seats are defective, and may inadvertently deploy despite the absence of impact.
In the braking system, the seal inside the master cylinder uses a material with insufficient cold resistance. When brake operation is performed at below-freezing ambient temperatures, the seal may deform and, in …
At the clutch release cylinder attachment point of the clutch pressure pipe, vibration during driving may cause hydraulic fluid to leak from the pipe attachment area, resulting in heavy clutch and steering …
The connector of the electrical wiring for the fuel pump installed in the fuel tank has improper crimping. Continued use in this condition causes increased contact resistance in the connector, reducing fuel …
The cooling water hose clamp attached to the engine body may contact the fuel return hose. If use continues in this condition, the fuel return hose may be damaged in the worst …
The fuel supply hose routing to the engine is improper, causing contact with the intake pipe. If use continues in this condition, the hose may be damaged in the worst case, resulting …
The passenger-side airbag has insufficient stitching strength at the back seam. Upon deployment, this seam may rupture, resulting in impaired airbag function.
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.