Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
5227 matching recalls · page 161 of 175
In the fuel system, the fuel pipe between the fuel pump and fuel filter has insufficient mounting support strength. Continued use in this condition may cause resonance due to engine vibration, leading …
In the steering lock mechanism of automatic transmission vehicles, the pin securing the key cylinder cap has improper interference fit. Continued use in this condition may cause the pin to protrude when …
The striker structure of the locking mechanism on resin-made bonnets (Mazdaspeed Aero Bonnets) sold as aftermarket parts is inadequately designed. Continued use in this condition may cause the welds of the striker …
The muffler heat shield bracket attachment structure is inadequate. Continued use in this condition may cause this section to fracture due to exhaust gas back-pressure vibration, resulting in exhaust leakage. The exhaust …
The mounting position of the fixing clamp, which is attached to the front-wheel brake hose to maintain clearance between the electrical wiring and tire, is inappropriate. Continued use in this condition may …
The load-sensing proportioning valve (LSPV) that controls brake force distribution between front and rear wheels in the braking system was not properly adjusted at the factory. Continued use in this condition may …
In the parking brake mechanism, the wedge fitting component that actuates the wheel cylinder piston may contain casting defects. Continued use in this condition could result in component fracture in the worst …
Improper routing of electrical wiring in refrigerated vehicles may cause the wiring to contact and be damaged by cooling system piping, resulting in short circuits and potential fire hazard if continued in …
In the braking system, some rivets securing the brake anchor pin have defective crimping. If use continues in this condition, the affected rivet may fracture, potentially resulting in degraded brake performance in …
A manufacturing defect in the acceleration sensor within the control unit that regulates the driver and passenger side airbag systems may cause unintended airbag deployment while driving in worst-case scenarios.
Gaps between the brake system air nylon tubing and exhaust manifold heat shield are inadequate in some cases. Continued use in this condition may cause the tubing to melt and deteriorate due …
Manufacturing defects in the hydraulic pressure adjustment valve within the ABS hydraulic control unit of the braking system may cause brake fluid leakage from the valve. In worst-case scenarios, the ABS and …
Rear wheel parking brake air chamber vent seal is inadequate, allowing water ingress into the chamber. Internal springs corrode and may fracture in severe cases, reducing parking brake effectiveness.
The automatic clearance adjustment device of the brake system may lack the installed arm bracket, preventing automatic adjustment of the brake drum-to-lining clearance. Continued operation in this condition may result in reduced …
In electric power steering systems, the contact surface treatment of the torque sensor (power assist amount control sensor) assembled in the gearbox is inadequate. Continued use in this condition may cause contact …
The wiring board in the audio unit of the sound system has an improper design, causing the board temperature to rise. Continued use in this condition may lead to capacitor degradation and …
The bolts securing the vibration damper on the steering gear box and the surface treatment of the steering gear box mounting surface have deficiencies. Despite being tightened to specification torque, some bolts …
Improper surface treatment on bolts securing the vibration damper of the steering mechanism and the steering gearbox mounting surface results in insufficient axial force despite proper torque specification. Continued use allows bolts …
The vacuum hose of the brake booster was manufactured using an inappropriate method. Continued use in this condition may cause cracks to develop at the hose end, potentially leading to vacuum loss …
The vacuum hose of the brake booster was manufactured using an improper method. Continued use in this condition may cause cracks to develop at the hose ends, and in the worst case, …
In the steering system, fastening of the upper arm attachment bolts on the steering knuckle is improper. If the vehicle continues to be used in this condition, cracks may develop in the …
The fuel hose routing and fixing method in the engine compartment is inadequate. Continued use in this state may cause the hose to be damaged by engine vibration, resulting in fuel leakage …
In vehicles equipped with ABS (Anti-lock Brake System) and hill start assist (EZGO), improper machining in the hydraulic control unit may cause brake pedal travel to increase during braking after ABS activation. …
In the engine, the electronic control variable nozzle opening setting of the turbocharger is inappropriate. When the compression release engine brake is activated, excessive force from gas flow acts on the turbocharger …
In the braking system, improper routing of the left front wheel brake pipe may interfere with the upper arm of the independent suspension. Continued use in this condition may cause damage to …
In the braking system, the welding of the mounting bracket for the air charge pipe that supplies air to the air tank is defective. Continued use in this condition may cause cracks …
The spot welds between the fuel tank top plate and baffle plate may be defective. Continued use in this condition could cause cracks to develop at the spot weld location, potentially resulting …
The airbag control module (airbag deployment control device) is mounted on the floor beneath the front passenger seat. If large quantities of water enter the cabin due to flooding or similar conditions, …
Improper assembly of the engine ignition switch may prevent the switch from returning to the off position after engine start. Continued operation in this state can result in starter damage, wiring short …
The control program for the brake force control device (ABS: Anti-lock Brake System) in the braking system is inappropriate. When braking is applied while operating the steering on rough roads and similar …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.