Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
5227 matching recalls · page 97 of 175
The heat shield for thermal discoloration prevention on the noise shield mounted on the frame of large trucks has insufficient strength, and cracks may develop due to vibration during operation. If continued …
In the parking brake of light-duty trucks, the double nut securing the cable to the lever may loosen due to insufficient tightening. Continued use in this condition can result in inadequate parking …
Improper routing of the power steering hydraulic hose may result in hose damage due to vehicle vibration during use, causing oil leakage and potential loss of steering control.
The pulse converter that converts vehicle speed signals to display vehicle speed has insufficient response capability to internal element voltage fluctuations, which may cause the element to burn out and render speed …
On trailer axles, the wire attachment position of the catch strap (a device that limits air suspension extension height) is improper, causing wire-to-axle interference on some units. Continued use in this condition …
In high center-of-gravity vehicles, the stabilizer arm strength of the rear axle air suspension is insufficient. Repeated rolling can cause cracks in the arm. Continued operation may result in arm fracture in …
Fire — null The engine bay insulation may have insufficient clearance from the turbocharger. As a result, there is a possible risk of fire in the engine compartment due to overheating of …
1. At the fuel tank pump motor wiring terminal connection, repeated thermal cycling causes the connection to loosen, resulting in poor contact that generates heat and electrical discharge. The terminal connection may …
1. At the fuel tank pump motor wiring terminal connector, repeated cycles of electrical heating and cooling cause the terminal connection to loosen, resulting in poor contact. This generates heat and electrical …
Brake light wiring is inadequately secured and may contact the brake linkrod. Continued operation in this state can result in wiring insulation damage and short-circuiting, causing the ABS warning light to illuminate …
In light trucks and buses, the fuel filter outlet connection has improper geometry in some units. Continued operation in this condition may cause the fuel tube to detach due to vibration during …
Injuries — null The wiper-arm mechanism may chafe against the brake booster vacuum line. If this occurs, it could lead to a gradual reduction of the power-assisted braking and more effort would …
In large trucks, snow adhering to and accumulating on the front panel may melt due to heat from heater hoses and other sources. When meltwater drips onto the adjustment valve (front axle) …
Large and medium-sized buses may have an improperly assembled piston installed in the hand control valve that operates the parking brake. Continued use in this condition may cause delayed parking brake actuation …
Defective wheel bearings for the front axle (with manufacturing defects in the bearing rolling elements) were mixed into the supply shipment. Some trucks and buses that had their front axle wheel bearings …
In light-duty trucks equipped with electronically controlled manual transmissions, the internal circuit of the motor drive unit that automatically controls clutch operation is defective. Excessive current flows during clutch motor operation, causing …
The supply-side rubber hose of the hydraulic power steering system has insufficient heat resistance. The rubber hose deteriorates and loses flexibility due to heat from the exhaust manifold catalytic converter. Consequently, hydraulic …
The hydraulic pump fastening structure of the agricultural tractor is inadequate, causing the pump gear plate (pump chamber) to shift when operating pressure increases, resulting in seizure of the input bearing area …
The edge of the metal electrical wire protective cover beneath the driver's seat is improperly finished with sharp edges, which can damage electrical wiring during cover installation. Continued use in this condition …
The high-pressure piping used in the power steering system is made of inappropriate material. Prolonged use may result in small holes developing in the high-pressure pipe due to water ingress, and additionally …
In garbage collection vehicles, the rear lighting fixture mounting position is improper, causing the tail light and brake light mounting positions to violate the Road Transport Vehicle Safety Standards (installation requirement: the …
Van-type vehicles have an improperly selected rear bumper for the underrun protection device, resulting in some rear bumpers with excessive width. Consequently, the outermost edge of the underrun protection device extends beyond …
The power wiring between the engine starter terminal and battery is routed improperly, causing the wiring to become pinched in the gap between the vehicle frame and transmission case. If continued in …
In vehicles equipped with automatic transmissions, the transmission skid plate (a protective shield mounted beneath the transmission) has an improper shape that may cause excessive accumulation of foreign material on the plate …
The pressure gauge displaying the pressure of the brake system pressurized reservoir equipped in the driver's cabin does not display the minimum effective operating pressure on its scale, failing to comply with …
The pressure gauge displaying the pressure of the brake system accumulator equipped in the driver's cabin does not indicate the minimum effective operating pressure on its scale, failing to comply with the …
In vehicles equipped with diesel engines, the sound insulation material in the engine compartment is improperly secured. Depending on the brake line assembly angle, the brake lines may push the sound insulation …
In proto-brand two-wheeled vehicles equipped with electronic fuel injection systems, the rubber material of the fuel hose is inappropriate, and insufficient consideration of design variation in the crimped components (sockets) has resulted …
The left rear door latch may have defective internal resin components due to manufacturing defects, preventing the lock mechanism from operating properly. This can result in the door failing to close securely, …
In agricultural chemical spray vehicle brake pipes, assembly variations may cause the brake pipe to contact nearby power steering hoses. Continued operation in this condition risks vibration-induced wear at the contact point, …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.