The seal of the gas injection valve in the brake accumulator is insufficient, allowing gas to leak. Continued use may result in decreased gas pressure, potentially extending brake stopping distance in worst-case …
Komatsu GD405A-3 2004–2005
Komatsu GD655-3 2004–2005
Komatsu GD755-3 2004–2005
小松メック GD405A-3 2004–2005
The gas injection valve seal of the brake accumulator is insufficient, allowing gas to leak. Continued use may result in decreased gas pressure, and in worst case, the parking brake may engage …
Komatsu WA380-5 2004–2005
Komatsu WA430-5 2004–2005
Komatsu WA470-5 2004–2005
小松メック WA500-3 2004–2005
The hose connecting the clutch master cylinder to the release cylinder has insufficient strength. Vibration during engine starting and similar operations may cause cracks to develop in the hose. Continued use allows …
Hino Hino Dutro 2003–2006
The balancer attached to the flip-up back door was manufactured using an improper process. Residual cleaning fluid remaining in the damper case causes the O-ring to swell, reducing damping force and increasing …
Mazda Scrum 2005–2006
Suzuki Every 2005–2006
In the suspension system of rear dual-axle heavy trucks (rear non-drive axles), the trunnion base of the rear axle has insufficient strength. Stress generated during minimum turning radius operation can cause cracks …
Mitsubishi Fuso 1996–2001
The positioning pin material of the rear brake caliper mounting bracket is inadequate. Under braking load, the pin may crack. Repeated loading causes crack propagation and eventual fracture, allowing the brake caliper …
Triumph Speed Triple 1050 2006
Triumph Sprint ST 691 2006
Large-type route non-step buses equipped with glide-slide front doors may have insufficient strength in the guide roller bracket due to improper welding between the support column and fixed bracket. Continued use risks …
Nissan - 2006
The fuel tank plate thickness was improperly altered during manufacturing, resulting in insufficient strength in some fuel tanks. Continued use in this condition may cause cracks to develop, potentially leading to fuel …
Komatsu HV3000-1 2000–2005
Due to a drafting error in the design specifications, the fuel return hose and supply hose are installed in reverse on the fuel tank. Additionally, the fuel return line is secured improperly, …
Komatsu HV3000-1 2000–2005
The welding of the secondary muffler located forward on the exhaust pipe is inadequate, and cracks may develop at the weld due to vibration during driving and other conditions. If use continues …
Subaru R1 2003–2005
Subaru R2 2003–2005
Front-wheel drive shafts may contain excessive moisture in the lubricating grease used in the wheel-side joint. This can cause temporary loss of the lubricant film when the steering is fully turned during …
Toyota bB 2002–2003
Toyota Will Cypher 2002–2003
Toyota ist 2002–2003
Toyota Vitz 2002–2003
Toyota Funcargo 2002–2003
+1 more
Due to improper mounting structure of the front impact sensor that detects collision impact early during offset collisions, the mounting bolts may loosen. Consequently, the sensor may fail to detect impact during …
Mitsubishi Outlander 2005–2006
The parking mechanism actuator lever of the automatic transmission (mechanism that mechanically locks the transmission output shaft) has improper machining. When shifted to park position, the lever interferes with the valve body, …
Mitsubishi i 2006
The passenger seat airbag folding method is improper, which may prevent full deployment during initial actuation due to contact resistance with the case sidewall. As a result, internal pressure within the airbag …
Mitsubishi i 2005–2006
In the manufacturing process, fastening bolts securing the transmission support member to the vehicle frame may not be tightened to the specified torque. Continued use in this condition may cause bolt loosening …
Isuzu Elf 2006
Nissan Atlas 2006
The door latch structure of the manual slide door is inadequate, allowing water from snowmelt and rain to accumulate inside the door latch. If water freezes at low temperatures, the door latch …
Mazda Premacy 2004–2006
In vehicles equipped with automatic doors, the automatic open/close switch capacitance is set improperly. When the switch is operated during door opening or closing, arc discharge occurs, causing contact wear and generation …
Isuzu Journey 2004–2006
Nissan Civilian 2004–2006
The relay, fuse, and electrical wiring for the heated windshield on snow removal vehicles have insufficient capacity. When used continuously for extended periods, the wiring may overheat. Continued use can result in …
Mitsubishi Fuso 1996–2005
Insufficient clearance between tire/wheel sidewall and rear axle. When steering is operated to maximum lock angle, tire/wheel sidewall may interfere with the rear axle. Continued use could damage the tire and, in …
S N FD30PX 2006
S N FT30PX 2006
On flip-up seats located adjacent to emergency exits in buses, some units have weak pin retention force securing the seat, some have insufficient overlap in anti-tip brackets due to installation variance, and …
Mitsubishi Fuso 1988–2002
Mitsubishi Fuso Aero Queen 1988–2002
Mitsubishi Fuso Aero Star 1988–2002
Mitsubishi Fuso Aero Bus 1988–2002
Mitsubishi Fuso Aero Midi 1988–2002
The engine oil pump unit mounting bolts are insufficiently tightened, which may cause oil leakage from the pump mating surface. Continued operation may result in reduced oil pressure, leading to inadequate engine …
ドカテイ GT1000 2006
ドカテイ ST3S ABS 2006
ドカテイ Monster S2R 1000 2006
ドカテイ Monster S4RS 2006
②Some flywheel mounting nuts have insufficient fastening torque and may loosen. Continued operation could result in the nut detaching, causing the flywheel to interfere with the stator coil, cracking the flywheel. In …
ドカテイ ST3 2005–2006
①The electrical wiring for the fuel pump is routed improperly in some cases, causing contact with the exhaust pipe. Continued operation in this condition may result in insulation melting and short-circuiting, potentially …
ドカテイ ST3 2005–2006
In the power transmission device, improper assembly method when attaching the hydraulic supply pipe to the travel motor may cause oil leakage at the connection point. Continued operation can lead to oil …
Mitsubishi GCR140 2003–2005
Mitsubishi GCR160 2003–2005
Injuries — Risk of handbrake cable coming loose. Possible opening of handbrake lever on rear brake caliper.
In the steering gear of the steering apparatus, the pinion shaft bearing may not be assembled during the manufacturing process. As a result, the pinion shaft may not be securely retained, and …
Nissan March 2002
The exhaust pipe immediately before the muffler has insufficient strength. Engine vibration may cause cracks to develop in the exhaust pipe. Continued use without remedy could result in crack propagation, potentially leading …
ヰセキ AT 46 2004–2005
The structural design of the resin vehicle-body mounting bracket for the back-door gas strut is inadequate, causing slack in the clip that secures the gas strut and vehicle-body stud ball. Repeated opening …
Mazda Familia 1999–2006
Nissan AD 1999–2006
Nissan Wingroad 1999–2006
Due to inadequate material specifications for the O-ring and improper tolerance control during manufacturing of the spacer in the vehicle speed sensor mounted on the final drive, the airtightness of the sensor …
BMW HP2 2005–2006
BMW R1200S 2005–2006
The oil pump that supplies hydraulic pressure to the continuously variable transmission has improper machining of the pump body assembly surface, which may cause the rotor and sliding surface to interfere due …
Honda Odyssey 2003