Due to improper engine control unit software programming, the fuel pump may continue operating after the ignition switch is turned off. This can cause fuel to leak from the injectors and accumulate …
Peugeot Peugeot 307 XS 2001–2004
Peugeot Peugeot 307 XS Break 2001–2004
Peugeot Peugeot 406 Sport 2001–2004
Peugeot Peugeot 607 2001–2004
In the keyless start system of the ignition switch, due to improper programming of the start control unit, the vehicle may not lock when outside the radio transmission range of the portable …
Suzuki Skywave 2006
The flange section of the rear axle shaft has insufficient strength. When driving repeatedly at high speed on winding mountain roads and similar routes, cracks may develop at the base of the …
Toyota Land Cruiser Prado 1996–1999
The ball bearing case of the wheel-side joint on the front drive shaft has insufficient strength. Repeated full-lock steering maneuvers can cause cracks to develop in the case. If the vehicle continues …
Chrysler Grand Voyager 1998–2000
Chrysler Voyager 1998–2000
The brake pedal attachment point on the primary braking system has insufficient structural margin. When the pedal attachment area corrodes and wears due to de-icing agents or similar substances, the structural strength …
日立 LX70-5 1999–2003
日立 LX80-5 1999–2003
In front axle braking systems, improper welding instructions for air-over-hydraulic booster mounting brackets result in some units not being securely welded to the vehicle body. This causes the booster to vibrate excessively …
Isuzu Erga 2001–2005
The parking brake cable has an improper guide roller mounting structure, which increases sliding friction between the cable and guide roller during parking brake operation. Continued use may cause cable wear, and …
Mercedes-Benz 416CDI 2005
Due to improper handling during engine transportation, some units had their oil filler caps loosened during the process. Continued use in this condition may cause oil to spray from the cap area …
Mazda MPV 2006
The electronic fuel injection pump's overvoltage protection device has insufficient capacitor capacity. Continued operation in this condition may cause the capacitor to short-circuit due to overvoltage generated during engine start-up and similar …
キャタピラー 924G 2002–2005
キャタピラー 924GZ 2002–2005
キャタピラー 928G 2002–2005
The gear shaft within the mechanical supercharger has insufficient strength, and cracks may develop due to vibration during operation. If use continues in this condition, the shaft may fracture, causing debris to …
BMW Alpina Alpina 2006
In the anti-lock braking system (ABS), the foreign object intrusion prevention cover structure for the front-wheel rotation speed sensor is inadequate. Flying stones and similar debris can strike and deform the sensor. …
Isuzu Elf 2000–2002
Due to improper programming of the fuel gauge control computer, fuel level may not display correctly and the low fuel warning light may not illuminate. Continued operation in this condition could result …
キャデラック STS 2005–2006
The hose length of the rollover shutoff valve (front) installed to connect the left and right fuel tanks to the canister is inappropriate. Continued use may cause the hose to fracture due …
Ferrari 360Spider 2003
In turbochargers with variable nozzles, the link mechanism that regulates intake air volume is inadequately designed. During transitions from low to high engine speeds, the variable nozzle fails to return to proper …
Hino Hino Profia 2003–2006
In variable-nozzle turbochargers for the engine, improper machining of the turbine housing shroud causes some units to have turbine blade interference. Continued operation in this condition may result in turbine blade fracture, …
Hino Hino Profia 2003–2006
In the engine's variable-nozzle turbocharger, ① some units have inadequate turbine blade material resulting in reduced strength; continued operation at high RPM can cause cracking. If operation continues in this condition, turbine …
Hino Hino Profia 2003–2006
Manufacturing defects in internal components of the seat belt retractor for the driver and front passenger seats can cause interference between the lock mechanism gear sensor end and guide holder, preventing the …
Lexus GS350 2005
Lexus GS 430 2005
Lexus IS250 2005
Lexus IS 350 2005
Some bolts fastening the horn switch to the steering wheel have insufficient strength. When the airbag deploys in extremely low temperatures, the pressure may fracture these bolts, causing the horn switch to …
Mazda Roadster 2005–2006
Certain drive chains for two-wheeled vehicles have insufficient material strength due to improper heat treatment during manufacturing. As a result, cracks may develop due to driving force during acceleration or deceleration, and …
アプリリア RSV1000R 2004
アプリリア RSV1000R FACTORY 2004
アプリリア TUONO1000R 2004
Improper routing of the accelerator cable causes stress concentration in the casing cap that secures the cable to the vehicle body, resulting in breakage in some cases. Continued operation may cause the …
Chevrolet MW 2000–2005
Suzuki Solio 2000–2005
Suzuki Wagon R 2000–2005
The ignition switch contact structure is inadequate. With extremely high switch usage frequency, wear particles generated during operation accumulate near the contacts and cause conductivity. Continued use may result in the starter …
Suzuki Every 1998–2000
Suzuki Carry 1998–2000
Suzuki Scrum 1998–2000
In ambulances, the rubber diaphragm in the brake booster has insufficient heat resistance. Thermal effects in the engine compartment may cause the diaphragm to thermally degrade and crack. Continued use risks crack …
Toyota Grand Hiace 1995–2005
Toyota Grand Hiace Van 1995–2005
Toyota Granvia 1995–2005
Toyota Granvia Van 1995–2005
Toyota Touring Hiace 1995–2005
+4 more
In the front propeller shaft for four-wheel drive vehicles, thermal management of the universal joint at the transfer side is insufficient. During high-load driving such as high-speed or climbing operation, the temperature …
Toyota Grand Hiace 1995–2005
Toyota Granvia 1995–2005
Toyota Granvia Van 1995–2005
Toyota Touring Hiace 1995–2005
Toyota Toyota Ambulance 1995–2005
+3 more
The carbon brush material in the fuel pump motor is inadequate, causing premature wear. Continued use allows wear to progress, and in the worst case, the fuel pump may become inoperable, resulting …
Volkswagen Passat 2.8 V6 4Motion 2002–2003
Volkswagen Passat Wagon 2.8 V6 4Motion 2002–2003
The motor within the fuel pump uses carbon brushes made of inappropriate material, causing premature wear in some units. Continued operation may accelerate wear, potentially resulting in fuel pump failure, engine stoppage, …
Audi Audi A4 1.8T Quattro 2002–2003
Audi Audi A4 3.0 quattro 2002–2003
Audi Audi A4 Avant 1.8T quattro 2002–2003
Audi Audi A4 Avant 3.0 quattro 2002–2003
Audi Audi A6 3.0 quattro 2002–2003
+1 more
Bearings with insufficient load capacity were installed in the final gearbox, causing premature wear and reduced sealing performance. Continued use may result in oil leakage from the wheel-side joint, with dispersed oil …
モト・グッツィ Breva 1100 2005–2006
モト・グッツィ Griso 2005–2006
On paint-specification wheels, paint was inadvertently applied to the tapered bolt hole section, causing certain bolts to loosen. Continued use in this condition may result in bolt detachment and, in the worst …
Bentley Arnage T 2004–2005
Improper plating treatment during shift lever manufacturing has reduced material strength in some units. Operating the shift lever may cause it to fracture, resulting in inability to shift. In severe cases, the …
丸山 Maruyama Stereo Sprayer SSA-S602DX 2006
In manual cab-tilt mechanisms of large and medium-duty trucks, the rebound cushion (rubber component that detects cab lock status) uses improper material, causing it to adhere to the hook hinge bracket. When …
Mitsubishi Fuso Fighter 1983–1999
During stabilizer link installation, inadequate work instructions have resulted in insufficient tightening of the attachment nut on some vehicles. Continued use in this condition may cause the nut to detach and the …
Mitsubishi Fuso Canter 2005