Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
5227 matching recalls · page 133 of 175
In large-capacity transit buses, the flywheel ring gear hardness and starter magnetic switch activation circuit wiring length are inappropriate. During start operation, the starter pinion may collide with the flywheel ring gear, …
The ball joint attachment bolts on the front and rear suspension arms are improperly tightened. Repeated severe driving such as circuit operation can cause the attachment bolts to loosen. Continued use may …
Improper machining during battery positive terminal manufacturing has caused cracks in the affected component, resulting in battery electrolyte leakage that may contact the right front wheel brake pipe. Continued operation in this …
Due to improper engine control unit software programming, the fuel pump may continue operating after the ignition switch is turned off. This can cause elevated fuel line pressure, potentially resulting in fuel …
The fuel pump impeller has an oversized outer diameter, causing it to swell from fuel absorption and thermal expansion at elevated fuel temperatures, resulting in interference with the impeller case. Continued operation …
On four-wheel drive vehicles, the weld between the coil spring seat (lower seat) of the rear suspension device and the rear axle beam is insufficient. Due to vibration during driving, the weld …
In vehicles modified as garbage trucks, the dump cylinder mounting position is inappropriate, causing the brake pipe mounting bracket on the rear differential or the brake pipe and mounting bracket to potentially …
The steering cylinder in the steering system has an improperly shaped piston seal. Repeated small steering corrections can cause this seal to deform. Continued operation in this condition may result in a …
The fuel tank mounting position is improper, so during high-speed driving, road debris may collide with the front of the fuel tank. If the debris has protrusions, it could pierce the tank, …
Certain rear-view mirror angle adjustment switches installed on the center console were lubricated with an inappropriate lubricant. When the switch is exposed to high temperatures, such as during parking in intense sunlight, …
Some clips used to prevent detachment of the connecting pin linking the brake pedal and push rod are improperly assembled and may fall off. This could cause the connecting pin to disengage, …
In the braking system, the welding of brackets that secure brake hoses to the vehicle body may be defective. Continued use in this condition can result in the weld separating due to …
The airbag control unit in the airbag system has improper programming, which may cause delayed signal processing of the deceleration sensor depending on front offset collision conditions. As a result, airbag deployment …
Manufacturing burrs may be present in the piston cup inside the brake master cylinder, which can cause cracks in the piston cup. If used in this condition, the piston cup may fracture …
The rack groove that controls fuel injection quantity in the fuel injection pump has insufficient strength, and the attachment method of the fuel injection pump to the engine is inappropriate. Continued operation …
The lock system of the gull-wing doors at the rear of the vehicle body has improperly set spring return force for the lock that engages with the catch, and improper reaction force …
The piston cup groove in the pressure-increasing cylinder of the hydraulic booster that augments brake pedal force has been machined improperly, resulting in insufficient air-tight sealing between the piston cup and piston …
Inadequate waterproofing of the fuel pump electronic control unit allows water ingress into the connector terminals connecting the electronic control unit and fuel pump, causing corrosion. This corrosion can lead to fuel …
The contact geometry of the side marker light switch inside the combination switch is improper. When the side marker light is operated while holding the combination switch at mid-stroke during lane changes …
In the steering control system, the gas spring fixing section that maintains the adjusted angle of the steering handle after adjustment to match the operator's posture lacks sufficient strength. Vibration from work …
The rear axle swing stopper lacks sufficient strength. During operation on uneven or inclined roads, if steering is applied while the swing stopper and axle are in contact, the stopper may deform. …
In the planetary carrier of the front axle secondary reduction gear, improper machining of the spline section of the shaft coupling may cause cracks to develop in the spline section under operating …
In the pneumatic braking system, a hose between the air compressor and air dryer was incorrectly installed, allowing undried air to be sent into the purge chamber. In winter, moisture in the …
Parking brake air chamber and backplate mounting bolts without heat treatment have been mixed in, resulting in insufficient strength. These bolts may fracture, causing the backplate to detach and the parking brake …
In large tourist buses, the idler pulley structure that supports the air conditioning drive belt is inadequately designed, causing grease that lubricates the pulley bearing to scatter. Continued operation in this condition …
In large tour buses, the idler pulley structure that supports the air conditioning drive belt is inadequately designed, causing lubricating grease to scatter from the pulley bearing. Continued operation in this condition …
On vehicles equipped with power steering, the knuckle arm has insufficient strength. Repeated use with frequent lock-to-lock steering or high-frequency steering operations can cause cracks to develop in the arm. If use …
The red lens of the rear combination lamp, which serves as both a tail light and brake light, has insufficient weather resistance. Prolonged exposure to strong sunlight causes gradual fading of the …
The steering cylinder piston seal groove and seal dimensions are inadequate, causing abnormal wear of the seal when frequent steering reversals are performed. Continued use in this condition may result in internal …
The rear-wheel brake hose routing is improper and may interfere with the powertrain forward hydraulic hose. If use continues, engine vibration may cause the brake hose to chafe and sustain damage, potentially …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.